Manual Kenwood TS-2000E (page 96 of 150) (English)

45743

Zoom out

Zoom in

1/150

15 OPERATOR CONVENIENCES

These keys and controls are available on the

Commander to control the Transporter.

Note:

◆

When the synconize operation is incomplete, the main display

of the Commander may disappear. In this case, press [SUB] to

re-syncronze.

◆

You cannot recall memory channels 100 to 299 using [ENT]

and the numeric keys.

To recall memory channels 100 ~ 299,

use [+]/ [–].

◆

You can recall only the memory channels that have HF/ 50 MHz

frequencies.

◆

Do not use VHF/ UHF frequencies that are suffering from the

harmonics of HF/ 50 MHz transmissions.

◆

The frequency control operations, such as the Tuning control

and RIT/ XIT control, are much slower than using direct controls,

because each control command (in steps of 10 Hz) is sent as

packet data.

◆

When you change the frequency continuously, using the Tuning

control or the MULTI/ CH control, the last entry of the

Commander frequency is reflected on the HF/ 50 MHz

transceiver.

◆

Since Sky Command II+ requires 2 VHF/ UHF frequencies,

check the operating frequencies carefully to avoid interference

with other parties.

◆

When the transceiver exits the Sky Command II+ operation, the

internal TNC retains the data transfer speed in Menu No. 47. If a

different data transfer speed is required for packet operation,

reconfigure it to the desired value.

USING A SEPARATE TRANSPORTER

If you have more than 2 TH-D7A and/or TM-D700A

transceivers, you can use one of the transceivers as

a “Transporter”. This transceiver is connected to the

TS-2000(X) via the RS-232C port, EXT SP jack, and

Mic connector of the base station and the other

TH-D7A or TM-D700A transceiver works as a

“Commander”. With this configuration, you can turn

the TS-2000(X) ON and OFF using the

“Commander”. Refer to the instruction manual of the

TH-D7A or TM-D700A for interfacing the transceiver

to the TS-2000(X) transceiver.

TS-2000 + TH-D7A/ TM-D700A (Transporter) Setup:

1 Configure the TH-D7A or TM-D700A as a

“Transporter” and connect all the necessary

cables to the TS-2000.

2 Select a frequency (HF/ 50 MHz band) on the

main transceiver of the TS-2000.

3 On the TS-2000 Press [MENU], then turn the

MULTI/ CH control to access Menu No. 62E.

4 Select a “CLIENT”.

5 Press [MENU] to complete.

6 Start the Transporter mode on the TH-D7A or

TM-D700A.

TH-D7A/ TM-D700A (Commander) Setup:

Configure the TH-D7A or TM-D700A as a

“Commander”. Refer to the SKY COMMAND II

chapter in the instruction manual to set up the

transceiver as a “Commander”.

You can use a “Commander” as described on

pages 84 and 86.

REPEATER FUNCTION (K-type ONLY)

This transceiver is capable of receiving signals on

one band and retransmitting them on another band.

For example, a signal received on the sub-receiver is

retransmitted on the main transceiver. Similarly, a

signal received on the main transceiver can be

retransmitted on the sub-receiver’s frequency.

You can use any available frequency on the main

transceiver or sub-receiver to receive and transmit.

However, you cannot retransmit the received signals

that are outside the available transmission

frequencies. Additionally, you must use a different

antenna for transmitting and receiving. For example,

if you receive a VHF signal on the sub-receiver, you

can retransmit it using UHF on the main transceiver.

You cannot retransmit the signal using VHF of the

main transceiver.

Note: For the repeater function to operate, the squelch levels of the

main transceiver and sub-receiver must be adjusted so that no

background noise can be heard.

LOCKED-BAND REPEATER

The transceiver always uses the same band to

receive, and retransmits the received signals on the

other band.

1 Select a desired receive frequency on the sub-

receiver.

2 Press [MAIN] and select a desired transmit

frequency on the main transceiver.

3 Adjust the squelch threshold level so that both

receivers mute.

4 Press [MENU], then turn the MULTI/ CH control to

access Menu No. 61A.

5 Select LOCKED, using [+].

•“ ” appears.

Note: You can also reverse the receive and transmit bands, so that

you receive on the main transceiver and transmit on the sub-

receiver’s frequency.

CROSS-BAND REPEATER

The cross-band repeater is unlike the lock-band

repeater in that both bands can be used to receive

signals. When a signal is received on one band, it is

retransmitted on the other band. To activate the

cross-band repeater, select CROSS in Menu No. 61A

in step 5.

Note:

◆

The Repeater function has its own Time-out Timer which is set at

3 minutes. This value cannot be changed.

◆

After activating the Repeater function, you cannot access Menu

Nos. other than 61A and 61B.

HANG TIME FOR REPEATER FUNCTION

If necessary, you can cause this transceiver to remain

in the transmit mode for 500 ms after signals drop.

Access Menu No. 61B and select “ON”.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood TS-2000E in the language / languages: English as an attachment in your email.

The manual is 2,89 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Kenwood TS-2000E Manual

Product: