45743
74
Zoom out
Zoom in
Previous page
1/150
Next page
66
SCAN
Scan is a useful function for hands-off monitoring of
your favorite frequencies. By becoming comfortable
with all types of Scan, you will increase your operating
efficiency.
This transceiver provides the following types of scans.
epyTnacS esopruP
lamroN
nacS
nacSOFV
ehtfodnaberitneehtsnacS
detcelesuoyycneuqerf
margorP
nacS
ycneuqerfcificepsehtsnacS
yromeMniderotssegnar
992~092slennahc
nacSzHM
nihtiwseicneuqerfehtsnacS
egnarzHM1a
yromeM
nacS
lennahC-llA
nacS
,slennahcyromeMllasnacS
992ot00morf
nacSpuorG
yromeMcificepsehtsnacS
spuorglennahc
llaC
nacS
OFV
dnalennahcllaCehtsnacS
ycneuqerfOFVtnerruceht
yromeM
lennahC
dnalennahcllaCehtsnacS
lennahcyromeMdetceleseht
lausiV
*nacS
OFV
gnitarepotnerrucehtsnacS
asallewsaycneuqerf
forebmundeificeps
wolebdnaevobaseicneuqerf
langisehT.ycneuqerftaht
silennahchcaefohtgnerts
hparg-rabanideyalpsid
yromeM
lennahC
slennahcyromeMehtsnacS
langisehtsyalpsiddna
anilennahchcaefohtgnerts
hparg-rab
* Visual Scan graphically shows how frequencies in a specific range
are busy.
Note:
While using CTCSS or DCS, Scan stops only for the signals that
contain the same CTCSS tone or DCS code that you selected.
When using S-meter Squelch, Scan stops when the received
signal strength matches or exceeds the S-meter setting. Scan
resumes 2 seconds after the signal level drops below the S-meter
setting.
Pressing and holding Mic [PTT] causes Scan to stop if it is
functioning on a non TX band. Pressing Mic [PTT] on the
scanning band causes Scan to stop.
Starting Scan switches OFF the Automatic Simplex Checker.
NORMAL SCAN
When you are operating the transceiver in VFO mode,
2 types of scanning are available.
VFO Scan
The transceiver scans the entire band of the
frequency you selected. For example, if you are
operating and receiving on the main transceivers
VFO A at 14.195.00 MHz, it scans all the
frequencies in the range of 30.00 kHz to
60.00000 MHz. (Refer to VFO frequency range
in the Specifications.)
Program Scan
By programming the start and end frequency in
Memory channels 290 ~ 299 {page 62}, you can
limit the scanning frequency range. Since there
are 10 memory channels (290 ~ 299) available for
specifying the start and end frequency, you can
select one or more (a maximum of 10) ranges to
scan. This is useful when you are waiting for a DX
station on a certain frequency but the station may
appear on slightly higher or lower frequency.
VFO SCAN
VFO Scan scans the entire frequency range that is
available for the current VFO. When the Program
Scan frequency range is not programmed or no Scan
Group is selected for the Program Scan, the
transceiver also scans the entire frequency range
available for the current VFO.
If one or more Program Scan frequency ranges are
programmed in memory channels 290 to 299:
1 Press [FUNC], [SCAN/ SG.SEL].
2 If one or more memory channels are selected for
the Program Scan, the selected channels are
displayed in a larger font on the main dot-matrix
display.
In this case, press [•/ DCS/SEL] to temporarily
deselect all the channels. When there are no Scan
Group channels selected, “VFO SCN MODE”
appears on the sub dot-matrix display.
3 Press [SCAN/ SG.SEL] to return to the current
VFO mode.
4 Press [SCAN/ SG.SEL] to start the VFO Scan.
Note:
While scanning, you can change the scan speed by turning the
RIT/ SUB control. Turn the control clockwise/ counterclockwise
to decrease/ increase the scan speed. The speed indicator
appears on the main dot-matrix display, where P1 is the fastest
speed and P9 is the slowest.
You cannot change the VFO Scan speed in FM mode.
You cannot change the VFO Scan speed on the sub-receiver.
74


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kenwood TS-2000E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood TS-2000E in the language / languages: English as an attachment in your email.

The manual is 2,89 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info