606708
56
Zoom out
Zoom in
Previous page
1/77
Next page
APRS-11
SELECTING A POSITION COMMENT
Enter Menu mode and access Menu 607.
The APRS data which you transmit always includes one of the
15 predetermined position comments. Select an appropriate
comment depending on your situation.
The selectable comments are listed below:
[Off Duty] [Enroute] [In Service] [Returning] [Committed] [Special]
[PRIORITY] [CUSTOM 0 ~ CUSTOM 6] [EMERGENCY!]
If you select “Emergency!”, a confi rmation message appears. Press
the Tuning control again.
ATTENTION: When it is unnecessary, never “EMERGENCY!”. When an
emergency signal is received using APRS, the Emergency Alarm on all
stations will sound.
STORING STATUS TEXT
Enter Menu mode and access Menu 608.
Text <TEXT>
Status text is another comment to transmit with position
data. Unlike a position comment, you can make any desired
comment using a maximum of 42 alphanumeric characters.
This transceiver has 5 memory channels for preprogramming.
1 Select a status text number.
• Press [USE] to mark the currently used status text with [ ].
2 Enter your status text.
Text Transmit Frequency <TX RATE>
Select the frequency on which to transmit the status text
when the APRS beacon is transmitted. You can select [OFF],
or [1/1] ~ [1/8] (APRS only).
1/X means the status text will be transmitted X number of times.
QSY FUNCTION
The QSY function uses AFRS (Automatic Frequency Reporting
System) to report a frequency on which voice communications
can be established. A station using the QSY function embeds
the frequency information in a position beacon transmission.
A receiving station of this information can change frequency,
or QSY, over to the reported voice frequency to begin voice
communication by the select of [TUNE].
Transmitting QSY Information
A properly confi gured functioning TM-D710G QSY station can
automatically embed the voice frequency from the non-data band
to the beginning of status text. This is the mechanism used for
automatically transmitting the frequency information.
The format of the transmitted frequency is FFF.FFF MHz.
So, for example, if at the time of a beacon transmission, the
non-data band has a frequency of 446.100 MHz selected, then
the frequency of “446.100MHz” gets embedded to the beginning
of the status text. If you confi gure in any of Statuses 1 through 4
the frequency of “446.100MHz” at the beginning of the status text
messages, then this fi xed frequency will be transmitted as QSY
information along with the beacon transmission. In addition to
frequencies, there are fi elds where you can send other settings
such as Wide/Narrow, Tone/CTCSS/DCS, Shift (+/-), and Offset
frequency simply by -leaving one space between each value.
Therefore, other information besides just a frequency can be
sent.
QSY Information Format:
(Insert one space after the frequency before entering Wide/
Narrow, Tone/CTCSS/DCS and Shift/Offset.)
“T079”: An upper case “T” indicates Wide. Tone frequency of 79.7
Hz. (Encoding)
“t079”: A lower case “t” indicates Narrow. Tone frequency of 79.7 Hz.
(Encoding)
“tOFF”: A lower case “t” indicates Narrow. Tone = OFF (Without any
tone Encoding or Decoding.)
“C079”: An upper case “C” indicates Wide. CTCSS frequency of 79.7
Hz. (Encoding/ Decoding)
“c079”: A lower case “c” indicates Narrow. CTCSS frequency of 79.7
Hz. (Encoding/ Decoding)
“D023”: An upper case “D” indicates Wide. DCS code of 023.
(Encoding/ Decoding)
“d023”: A lower case “d” indicates Narrow. DCS code of 023.
(Encoding/ Decoding)
“+” : Plus Shift (A default offset frequency is applied.)
“–” : Minus Shift (A default offset frequency is applied.)
“+500” : Plus Shift, 5 MHz Offset
“–060”: Minus Shift, 600 kHz Offset
The value of the Offset shall be a 3-digit number. (x 10 kHz/ 50
kHz step)
Refer to the website for QSY Information Format:
http://aprs.org/info/freqspec.txt (as of October 2013)
56


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kenwood TM-D710GE at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood TM-D710GE in the language / languages: English as an attachment in your email.

The manual is 7,22 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kenwood TM-D710GE

Kenwood TM-D710GE User Manual - English - 55 pages

Kenwood TM-D710GE User Manual - German - 74 pages

Kenwood TM-D710GE User Manual - Dutch - 75 pages

Kenwood TM-D710GE User Manual - Dutch - 55 pages

Kenwood TM-D710GE User Manual - French - 77 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info