606708
27
Zoom out
Zoom in
Previous page
1/77
Next page
EchoLink-2
Selecting a Transmit Speed
Some repeaters may not respond correctly if a code is
transmitted at fast speed. If this happens, change the
EchoLink transmission speed from FAST (default) to SLOW.
1 Enter Menu mode and access Menu 205.
2 Set the speed to FAST or SLOW.
SETTING UP EchoLink Sysop MODE
Connect the TM-D710G to a personal computer to use the
system as a node station for EchoLink relaying.
When connecting to a personal computer and using the
EchoLink Sysop mode, the hard fl ow control operation RTS and
CTS computer terminals operate the same as and are changed
with the SQC (squelch control signal output to the computer)
and PKS (transmit control signal input from the computer) data
terminals.
The current band becomes the same as the data band which is
selected in menu No. 918 regardless of the transmission band
and operation band.
Use the PG-5H (interface cable kit) when connecting to a
personal computer.
Data communications cable
Serial communications cable
To PC audio terminal
Pink: To microphone input terminal
Green: To line out terminal
To PC 9-pin D-SUB terminal
1 Turn the transceiver power OFF.
2 Press [PF2] + Power ON to turn EchoLink Sysop Mode ON.
• The icon appears on the display when EchoLink Sysop mode
is ON.
When the audio signal is output to the PC side, the
icon
blinks.
To turn EchoLink Sysop Mode OFF, press [PF2] + Power ON
again.
EchoLink Sysop Mode ON EchoLink Sysop Mode OFF
PC
terminal
PC
PC
terminal
PC
TxD
RxD TxD
RxD
RxD
TxD RxD
TxD
SQC
CTS RTS
CTS
PKS
RTS CTS
RTS
GND
GND GND
GND
Note:
When using EchoLink Sysop mode, perform the following settings (1) ~ (4).
(1) Set the SQC output setting (Menu No. 921) to “SQL”.
(2) When unnecessary noise signals, etc., are sent from the link station
to the internet while CTCSS and DCS are active, use can verify the
usage condition of the operating frequency by setting “EchoLink RX
Monitor” ([Edit] > [Menu] > [Transmit/Receive]) via the MCP-6A to
“Busy Only”.
Because of this, when EchoLink Sysop mode is ON, all received
signals on the DATA band are output from the speaker irregardless of a
matching CTCSS or DCS signal.
(Voice signals are output from the DATA terminal only when the
CTCSS or DCS signals match.)
(3) To avoid having the EchoLink software detecting a busy state even
when the transceiver power is turned OFF, set the “SQC Output Logic”
([Edit] > [Data Terminal]) via the MCP-6A to “High”.
(When performing this setting, ensure that the EchoLink’s software
“Invert Sense” setting in the RX Ctrl tab of the Sysop Setup window is
not checked.)
(4) When the audio level adjustment range on your personal computer is
insuffi cient, adjust the AF output level “PR1 Pin Output Level” ([Edit] >
[Data Terminal]) and AF input sensitivity “PKD Pin Input Level” ([Edit]
> [Data Terminal]) of the transceiver via the MCP-6A. Adjustments can
be made in steps of 6dB.
The settings in numbers 2 ~ 4 (above) can be performed only using a MCP-
6A.
When EchoLink Sysop mode is ON, it cannot communicate with the MCP-
6A. When using the MCP-6A, be sure to turn EchoLink Sysop mode OFF.
27


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kenwood TM-D710GE at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood TM-D710GE in the language / languages: English as an attachment in your email.

The manual is 7,22 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kenwood TM-D710GE

Kenwood TM-D710GE User Manual - English - 55 pages

Kenwood TM-D710GE User Manual - German - 74 pages

Kenwood TM-D710GE User Manual - Dutch - 75 pages

Kenwood TM-D710GE User Manual - Dutch - 55 pages

Kenwood TM-D710GE User Manual - French - 77 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info