606708
23
Zoom out
Zoom in
Previous page
1/77
Next page
SIGNALING-3
5 Enter your desired DCS code using the microphone keypad.
Refer to the table below for DCS codes.
DCS Code
023 025 026 031 032 036 043 047
051 053 054 065 071 072 073 074
114 115 116 122 125 131 132 134
143 145 152 155 156 162 165 172
174 205 212 223 225 226 243 244
245 246 251 252 255 261 263 265
266 271 274 306 311 315 325 331
332 343 346 351 356 364 365 371
411 412 413 423 431 432 445 446
452 454 455 462 464 465 466 503
506 516 523 526 532 546 565 606
612 624 627 631 632 654 662 664
703 712 723 731 732 734 743 754
DCS CODE SCAN
This function scans through all DCS codes to identify the
incoming DCS code on a received signal. You may fi nd it useful
when you cannot recall the DCS code that the other persons in
your group are using.
1 Press [TONE] 3 times to activate the DCS function.
• The icon appears on the display when the DCS function is
ON.
Each press of [TONE] changes the selection as follows:
Tone (
) CTCSS ( ) DCS ( ) Cross Tone ( :
default) Off (no display).
2 Press [F], [T.SEL] (1s).
• The icon blinks and “SCAN” appears on the display.
Scan starts when a signal is received.
To reverse the scan direction, turn the Tuning control clockwise
(upward scan) or counterclockwise (downward scan). You can
also press microphone [UP]/ [DWN].
To quit the scan, press [ESC].
When a DCS code is identifi ed, the identifi ed code appears on
the display and blinks.
3 Press the Tuning control to program the identifi ed code in
place of the currently set DCS code.
The DCS function will remain ON. To cancel DCS, press [TONE]
until DCS no longer appears on the display.
• Press [ESC] if you do not want to program the identifi ed code.
• Rotate the Tuning control while an identifi ed code is blinking, to
resume scanning.
USING CROSS TONE
You can set separate signaling types by TX and RX for when you
access a repeater that uses different Encode/ decode signaling.
To turn the Cross Tone function On:
Press [TONE] 4 times to activate the Cross Tone function.
• The ” (default) icon appears on the display when the Cross
Tone function is On.
Each press of [TONE] changes the selection as follows:
Tone (
) CTCSS ( ) DCS ( ) Cross Tone ( :
default) Off (no display).
Selecting a Cross Tone mode
To select the cross tone/code frequency required to access
your desired repeater:
1 Turn the Cross Tone function On.
2 Press [F], [T.SEL].
The Cross Tone setting appears on the display.
3 Rotate the Tuning control to select your desired Cross
Tone setting.
Setting Encode Decode Icon
DCS OFF DCS off
TO DCS Tone DCS
DCS CT DCS CTCSS
TO CT Tone CTCSS
To exit the Cross Tone setting selection, press [ESC].
4 Press any key other than the Tuning control and [ESC] to
complete the setting.
23


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kenwood TM-D710GE at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood TM-D710GE in the language / languages: English as an attachment in your email.

The manual is 7,22 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kenwood TM-D710GE

Kenwood TM-D710GE User Manual - English - 55 pages

Kenwood TM-D710GE User Manual - German - 74 pages

Kenwood TM-D710GE User Manual - Dutch - 75 pages

Kenwood TM-D710GE User Manual - Dutch - 55 pages

Kenwood TM-D710GE User Manual - French - 77 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info