511233
41
Zoom out
Zoom in
Previous page
1/64
Next page
36
OPERATOR CONVENIENCES
BATTERY LIFE
Before you operate the transceiver outside using a
battery pack, it is important to know how long you can
operate the transceiver. The following operating time
is measured under the condition of TX: 6 seconds,
RX: 6 seconds, and Stand-by: 48 seconds cycles.
We recommend you carrying extra battery packs, in
case the battery pack is discharged.
yrettaB
epyT
tuptuO
rewoP
/emiTgnitarepO
).xorppA(sruoH
m2 m52.1 mc07
L24-BP
)V4.7(
H5.60.60.6
L0.215.115.11
LE0.615.515.41
31-TB
)V0.6(
H0.5
L0.6
LE0.8
BATTERY REMAINING
You can confirm the remaining battery capacity using
this function. Confirm the battery type {below} prior to
use this function. To check the remaining capacity:
1 Press [F], [LOW].
The battery remaining indicator appears.
: High battery power
: Medium battery power
: Low battery power
: Needs recharging or replace the
batteries
2 Press [ ] or [MNU] to exit the Battery remaining
display mode.
Note: If you press [F], [LOW] while charging, “CHARGE” or
“STANDBY” appears {page 2}.
BATTERY TYPE
Before estimating the remaining battery capacity, set
the battery type in Menu No. 30 (BATTERY) to the
same type of battery that your are using (either
Lithium or alkaline).
1 Press [MNU].
2 Turn the Tuning control or press [ ]/ [ ] to select
Menu No. 30 (BATTERY).
3 Press [ ] or [MNU].
4 Turn the Tuning control or press [ ]/ [ ] to select
the battery type from “LITHIUM” and “ALKALINE”.
5 Press [ ] or [MNU] to store the setting.
Otherwise, press [ ] or [PTT] to cancel.
APO (Auto Power OFF)
The transceiver switches OFF automatically if no
keys or controls are pressed or adjusted, and no
signal is received for 30 minutes (default). 1 minute
before the transceiver switches OFF, warning beeps
sound for a few seconds and “APO” blinks. Then, the
transceiver turns OFF automatically. You can select
the APO time from OFF (disable), 30 (default), and
60 minutes.
1 Press [MNU].
2 Turn the Tuning control or press [ ]/ [ ] to select
Menu No. 18 (APO).
3 Press [ ] or [MNU].
4 Turn the Tuning control or press [ ]/ [ ] to select
the APO time from OFF, 30, or 60 minutes.
5 Press [ ] or [MNU] to store the setting.
Otherwise, press [ ] or [PTT] to cancel.
Note:
The APO function does not work if the transceiver is scanning.
When Tone Alert is ON, APO does not turn the power OFF.
The APO timer starts counting down the time when no key
presses, no control adjustments, and no command (SP/MIC jack)
sequences are detected.
The APO warning beep sounds even if Menu No. 19 (KEY
BEEP) {page 37} is selected “OFF”.
ATTENUATOR
The attenuator function is useful when extremely
strong signals exist nearby your receiving frequency.
When these type of signals are present, the receiver
gain control may be erroneously controlled and
overloaded by the strong signals, rather than by the
target receiving signal. If this happens, the target
receiving signal can be masked and buried by the
strong signals. In this case, turn the Attenuator
(approx. 20 dB) function ON. However, as a side
effect, the target signal is also attenuated. You may
have to adjust the VOL control to increase the audio
output level when it is ON.
1 Press [F], [MONI].
“ATT ON” appears for 2 seconds on the display
and the mode indicator starts blinking.
2 To turn the attenuator function OFF, press [F],
[MONI] again.
The mode indicator quits blinking.
Note:
When the attenuator function is ON, both A and B-band, are
attenuated. You cannot set the attenuator function independently
for each band.
“ATT ON” does not appear while scanning.
41


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kenwood TH-F7E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood TH-F7E in the language / languages: English as an attachment in your email.

The manual is 1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kenwood TH-F7E

Kenwood TH-F7E User Manual - Dutch - 64 pages

Kenwood TH-F7E User Manual - French - 64 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info