511233

Kenwood TH-F7E Manual

17
Zoom out
Zoom in
Previous page
1/64
Next page
12
OPERATING THROUGH REPEATERS
Repeaters, which are often installed and maintained
by radio clubs, are usually located on mountain tops
or other elevated locations. Generally they operate at
higher ERP (Effective Radiated Power) than a typical
station. This combination of elevation and high ERP
allows communications over much greater distances
than communications without using repeaters.
Most repeaters use a receive and transmit frequency
pair with a standard or non-standard offset (odd-split).
In addition, some repeaters must receive a tone from
the transceiver to allow it to access. For details,
consult your local repeater reference.
OFFSET PROGRAMMING FLOW
If you store the above data in a memory channel, you
need not reprogram every time. See “MEMORY
CHANNELS” {page 15}.
PROGRAMMING OFFSET
First select an amateur radio repeater downlink
frequency on the A-band or B-band as described in
“SELECTING A FREQUENCY” {page 7}.
■ Selecting Offset Direction
Select whether the transmit frequency will be
higher (+) or lower (–) than the receive frequency.
Press [F], [REV] to select the offset direction.
• “+” or “–” appears, indicating which offset
direction is selected.
• To program –7.6 MHz offset on the TH-F7E
(430 MHz only), repeatedly press [F], [REV]
until “ ” appears.
If the offset transmit frequency falls outside the
allowable range, transmitting is inhibited. In this
case, adjust the receive frequency so that the
transmit frequency is within the band limits.
Note: While using an odd-split memory channel or transmitting,
you cannot change the offset direction.
■ Selecting Offset Frequency
To access a repeater which requires an odd-split
frequency pair, change the offset frequency from
the default which is used by most repeaters. The
default offset frequency on the 2 m band is
600 kHz (all models); the default on the 70 cm
band is 5.0 MHz (TH-F6A) or 1.6 MHz
(TH-F7E); the default on the 1.25 m band is
1.6 MHz (TH-F6A).
1 Press [BAND] to select an amateur radio band
you want to change the offset frequency.
2 Press [MNU].
3 Turn the Tuning control or press [ ]/ [ ] to
select Menu No. 6 (OFFSET).
4 Press [ ] or [MNU].
5 Turn the Tuning control or press [ ]/ [ ] to
select the appropriate offset frequency.
• The selectable range is from 0.00 MHz to
59.95 MHz in steps of 50 kHz.
6 Press [ ] or [MNU] to store the setting.
Otherwise, press [PTT] to cancel.
TH-F7E only: If you have selected “ ” for the offset direction,
you cannot change the default (–7.6 MHz) offset frequency.
Note: After changing the offset frequency, the new offset
frequency will also be used by Automatic Repeater Offset.
TX: 144.725 MHz
TX tone: 88.5 Hz
RX: 145.325 MHz
TX: 144.725 MHz
TX tone: 88.5 Hz
RX: 145.325 MHz
Select a band.
q
w
e
r
t
y
Select a receive frequency.
Select an offset direction.
Select an offset frequency.
(only when programming odd-split
repeater frequencies)
Activate the Tone function.
(If necessary)
Select a tone frequency.
(If necessary)
… 17 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kenwood TH-F7E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood TH-F7E in the language / languages: English as an attachment in your email.

The manual is 1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kenwood TH-F7E

Kenwood TH-F7E User Manual - Dutch - 64 pages

Kenwood TH-F7E User Manual - French - 64 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info