606428
3
Zoom out
Zoom in
Previous page
1/8
Next page
C
REPEATER OPERATION
Note:
Please consult your dealer for programming the repeater.
Due to the frequency stability on the 6.25 kHz bandwidth channel,
when operating the repeater using an optional OCXO unit, allow
the unit to warm up after turning the power on. Refer to the KXK-3
instruction manual concerning the warm up duration.
After turning on the power, wait for approximately 10 seconds for
the VCXO or 5 minutes for the OCXO (when mounting) to warm up.
During this time, the CH/STATUS Display will blink. The keys will
function when they are pressed.
When power is applied to the unit, the
POWER
indicator lights
green. Turn the
VOLUME
control clockwise until a click sounds,
to unmute the audio. Rotate to adjust the audio. Turn the
VOLUME
control counterclockwise fully to mute the audio.
The
BUSY
indicator lights green while receiving a signal and the
TX
indicator lights red while transmitting.
Rear Panel
q
RX
IN
jack
Connect an RX antenna or a duplexer to this BNC
receptacle.
w
TEST/SPKR jack
Test input/output jack. Connect an external speaker to
this jack.
e
CONTROL I/O jack
Connect a repeater controller or a remote panel to this
DB-25 interface.
r
SYNC 1 / 2 jack
Connect to another repeater to use synchronous frame
signaling for digital trunking.
t
LAN jack
Connect to Ethernet.
CONTROLS AND FUNCTIONS
Front Panel
q
wrt
yu
io
e
q
w
rt y
u
e
MICROPHONE
VOLUME
COM
OFF/
POWERCTRL OCXO BUSY TX
12
MON
TAKE
OVER
RPT
DISABLE
ABC
345678
STATUS
TEST/SPKR
RX TX
CONTROL I/O
SYNC
12
LAN REF OUT REF IN
FUSE
75
DC 13.8V
y
REF OUT jack
Connect to another repeater within the site to supply a
reference signal.
u
REF IN jack
Connect from another repeater within the site to receive a
reference signal.
i
FUSE
Insert 7.5 A blade fuse into this fuse holder.
o
DC
13.8V jack
Connect a 13.8 V DC power supply to this jack.
!0
TX
OUT
jack
Connect a TX antenna or a duplexer to this BNC receptacle.
i
o
!0
TRANSCEIVER OPERATION
Receive
Adjust the volume to your desired level. You may need to
readjust the volume if you are having interference while receiving
a message from your dispatcher or another member in your fleet.
The
BUSY
indicator lights green while a signal is being received.
Transmit
1
Listen to the channel before transmitting, to make sure it
is not being used.
2
Press the microphone
PTT
switch, then speak in your
normal speaking voice.
The
TX
indicator lights red while transmitting.
3
When you finish speaking, release the
PTT
switch.
!0
!
1
!
2
q
Speaker
w
CH/STATUS Display
Two 17-segment digits display the channel number, name,
or status.
e
STATUS
indicator
Indicates the status of the repeater. (NXDN mode)
r
Programmable Function keys
Press these keys to activate their programmable
functions.
t
COM jack
Connect to the PC using a RS-232C standard DB9
(Female) cross cable.
y
VOLUME
control
Turn clockwise until a click sounds, to unmute the audio.
Rotate to adjust the audio. Turn counterclockwise fully to
mute the audio.
u
MICROPHONE
jack
Connect a microphone to this 8-pin modular jack.
i
POWER
indicator
Lights green when power is supplied to the
DC 13.8V
jack. Blinks red when an abnormal voltage is present.
While blinking, the repeater cannot be used.
o
TX
indicator
Lights red while transmitting.
!0
BUSY
indicator
Lights green while a signal is being received.
!1
OCXO
indicator
The OCXO indicator shows the state of the reference
10 MHz oscillator :
Lights Green when using a reference signal from an
optional OCXO unit (KXK-3).
Lights Orange when using a reference signal from another
repeater.
Lights red when no reference signal is available or when
an error occurs.
Does not light when the reference signal is an internal
VCXO signal.
!2
CTRL
indicator
The CTRL indicator shows the control channel status
while using Digital trunking :
Lights Green when the repeater is used as control channel.
Blinks Green when using a non-dedicated control channel.
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kenwood NXR-901 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood NXR-901 in the language / languages: English, French, Spanish as an attachment in your email.

The manual is 0,18 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info