606424
25
Zoom out
Zoom in
Previous page
1/39
Next page
18
Identifi cation Codes
An ID code is a combination of a 3-digit Fleet number and a 4-digit ID number.
Each transceiver must have its own Fleet and ID number.
Enter a Fleet number (100 ~ 349) to make a fleet call.
Enter an ID number (1000 ~ 4999) to make an individual call in your fleet.
Enter a Group ID (which is programmed in the FPU) to make a group call.
Enter a Fleet number followed by an ID number to make an individual call in your
desired fleet (Inter-fleet call).
Select “ALL” Fleet and “ALL” ID to make a call to all units (Broadcast call).
Select “ALL” Fleet and enter an ID number to make a call to the selected ID in all
fleets (Supervisor call).
Note:
Broadcast and Supervisor calls are programmed functions that cannot be made with a keypad.
The ID range may be limited by programming.
STATUS MESSAGE
You can send and receive 2-digit Status messages which may be decided in your
talk group. Messages can contain up to 16 alphanumeric characters. Status
messages range from 10 to 99 (80 ~ 99 are reserved for special messages).
A maximum of 15 received messages can be stored in the stack memory of your
transceiver. These saved messages can be reviewed after reception. Depending
on your dealer settings, when the stack memory is full, either the oldest message will
be erased when a new message is received or the new message will not be stored in
the stack memory. The icon lights when a message is stored in the stack memory.
Transmitting
1 Select your desired zone and channel.
2 Press the key programmed as Status to enter Status mode or Selcall +
Status to enter Selcall mode.
When using the Status key to enter Status mode, the target Fleet/ ID is fixed and
cannot be selected. Skip to step 5 to continue.
3 In Selcall mode, press the / keys to select the ID of the station you
want to call.
If Manual Dialing is enabled, you can enter the station ID by using the
microphone keypad, or by using
the / keys. When using the / keys,
cycle through the digits to select a digit, then press the key to set
the digit and move the cursor to the right. Repeat this process until the
entire ID is entered.
4 Press the key enter Status mode.
5 Press the / keys to select the status ID you want to transmit.
If Manual Dialing is enabled, you can enter the station ID by using the microphone
keypad, or by using
the / keys. When using the / keys, cycle through
the digits to select a digit, then press the key to set the digit and move
the cursor to the right. Repeat this process until the entire ID is entered.
25


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kenwood NX-901 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood NX-901 in the language / languages: English as an attachment in your email.

The manual is 0,42 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kenwood NX-901

Kenwood NX-901 User Manual - French - 39 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info