Manual Kenwood NX-720HG (page 7 of 72) (English, French, Spanish)

606418

Zoom out

Zoom in

1/72

GETTING STARTED

Note: The following instructions are for use by your KENWOOD dealer, an authorized KENWOOD

service facility, or the factory.

SUPPLIED ACCESSORIES

Carefully unpack the transceiver. We recommend that you identify the items listed below

before discarding the packing material. If any items are missing or have been damaged

during shipment, ﬁ le a claim with the carrier immediately.

DC power cable (with fuses). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

• 15 A fuse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Mounting Bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Screw set

• 5 x 16 mm self-tapping screw. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

• M4 x 6 mm hex-headed screw with washer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

• Spring washer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

• Flat washer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Microphone (with cable)

• KMC-35 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Microphone hanger (with 4 x 16 mm self-tapping screws) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Instruction manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

PREPARATION

Various electronic equipment in your vehicle may malfunction if they are not properly protected from

the radio frequency energy which is present while transmitting. Typical examples include electronic

fuel injection, anti-skid braking, and cruise control. If your vehicle contains such equipment, consult

the dealer for the make of vehicle and enlist his/her aid in determining if they will perform normally

while transmitting.

■ Power Cable Connection

The transceiver operates in 12 V negative ground systems only! Check the battery polarity and

voltage of the vehicle before installing the transceiver.

1 Check for an existing hole, conveniently located in the ﬁ rewall, where the power

cable can be passed through.

• If no hole exists, use a circle cutter to drill a hole, then install a rubber grommet.

2 Run the power cable through the ﬁ rewall and into the engine compartment.

3 Connect the red lead to the positive (+) battery terminal and the black lead to the

negative (–) battery terminal.

• Place the fuse as close to the battery as possible.

4 Coil the surplus cable and secure it with a retaining band.

• Be sure to leave enough slack in the cables so the transceiver can be removed

for servicing while keeping the power applied.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood NX-720HG in the language / languages: English, French, Spanish as an attachment in your email.

The manual is 0,87 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Kenwood NX-720HG Manual

Product: