606365

Kenwood NX-5700B Manual

9
Zoom out
Zoom in
Previous page
1/44
Next page
PREPARATION
　
　
　
WARNING
Various electronic equipment in your vehicle may malfunction if they are not properly protected from
the radio frequency energy which is present while transmitting. Typical examples include electronic
fuel injection, anti-skid braking, and cruise control. If your vehicle contains such equipment, consult
the dealer for the make of vehicle and enlist his/her aid in determining if they will perform normally
while transmitting.
o
Connecting the power cable
　
　
　
CAUTION
The transceiver operates in 12 V negative ground systems only! Check the battery polarity and voltage
of the vehicle before installing the transceiver.
1
Check for an existing hole, conveniently located in the firewall, where the power
cable can be passed through.
●
If no hole exists, use a circle cutter to drill a hole, then install a rubber grommet.
2
Run the power cable through the firewall and into the engine compartment.
3
Connect the red lead to the positive (+) battery terminal and the black lead to the
negative (–) battery terminal.
●
Place the fuse as close to the battery as possible.
4
Coil the surplus cable and secure it with a retaining band.
●
Be sure to leave enough slack in the cables so the transceiver can be removed for
servicing while keeping the power applied.
o
Installing the transceiver
　
　
　
WARNING
For passenger safety, install the transceiver securely using the supplied mounting bracket and screw
set, so the transceiver will not break loose in the event of a collision.
Note:
●
Before installing the transceiver, check how far the mounting screws will extend below the
surface. When drilling mounting holes, be careful not to damage vehicle wiring or parts.
1
Mark the position of the holes in the dash, using the mounting bracket as a
template. Using a 5/32 inch (4.2 mm) drill bit, drill the holes, then attach the
mounting bracket using the supplied screws.
●
Mount the transceiver within easy reach of the user and where there is sufficient space
at the rear of the transceiver for cable connections.
2
Connect the antenna and the supplied power cable to the transceiver.
3
Slide the transceiver into the mounting bracket and secure it using the supplied
hex-headed screws.
7
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kenwood NX-5700B at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood NX-5700B in the language / languages: English, French, Spanish as an attachment in your email.

The manual is 1,13 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info