157427
57
Zoom out
Zoom in
Previous page
1/64
Next page
57
Knowledge section
In case of difficulty
Operation to reset
The microcomputer may fall into malfunction (impos-
sibility to operate, erroneous display, etc.) when the
power cord is unplugged while unit is ON or due to
an external factor. In this case, execute the following
procedure to reset the microcomputer and return it
to normal condition.
Unplug the power cord from the power outlet then,
while holding the CD Open close (0) key depressed,
plug the power cord again.
After some time, the power will be switched off
and return will be made to the initial status.
÷ Please note that resetting the microcomputer clears
the contents stored in and it returns to condition when
it left the factory.
What seems to be a malfunction is not always so. Before calling for service, check the following table
according to the symptom of your trouble.
RemedyCauseSymptom
Amplifier section/Speakers
÷ Connect properly referring to
System
c
onnection”.
÷ Adjust to an required volume.
÷ Switch MUTE OFF.
÷ Unplug the headphone plug.
÷ Turn the unit OFF, remove the short-
circuit and turn the unit ON again.
÷ Insert correctly.
÷ Connect properly referring to “System
connection”.
÷ Adjust the optimum left and right bal-
ance.
Sound is not produced.
No sound from the head-
phones.
Sound is not produced from
the left or right speakers.
÷ The speaker cords are disconnected.
÷ The volume control is set to the mini-
mum position.
÷ The MUTE key is switched ON.
÷ The headphone plug is inserted into the
jack.
÷ The speaker cords are short-circuited.
÷ Imperfect insertion.
÷ The speaker cords are disconnected.
÷ The BALANCE is set completely to the
left or right channel.
RemedyCauseSymptom
÷ Adjust the present time again.
÷ Adjust the present time again.
÷ Adjust the present time referring to
“Clock adjustment”.
÷ Set the timer ON time and OFF time.
÷ Press the ON STANDBY key to set up
the execution.
÷ Connect antennas.
÷ Select a band.
÷ Tune to the frequency of the desired
station.
÷ Install the outdoor antenna in an apart
position from the road.
÷ Switch the suspected electric appliance
OFF.
÷ Install the TV or the system at an in-
creased distance between them.
÷ Preset stations with tunable frequen-
cies.
÷ Preset stations again.
The clock display blinks
without changing the fig-
ures.
Timer operation is not pos-
sible.
Radio stations cannot be
received.
Noise interferes.
A station has been preset but
it cannot be received by
pressing the P.CALL key.
÷ There was a power failure.
÷ The power cord was unplugged from the
outlet.
÷ The present time has not been adjusted
or there was a power failure.
÷ The timer ON time and OFF time have
not been set.
÷ The timer execution was not set up.
÷
The antennas have not been connected.
÷ A proper broadcasting band has not been
selected.
÷ The frequency of the station to be re-
ceived is not tuned.
÷ Car ignition noise.
÷ Influence of an electric appliance.
÷ A TV set is installed near the system.
÷ The frequency of the preset station is
not tunable.
÷ The preset memory has been cleared
because the power cord has been un-
plugged for a long period.
$
$
t
7
*
)
8
&
&
8
&
Tuner section
57


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kenwood nv 500 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood nv 500 in the language / languages: English as an attachment in your email.

The manual is 1,91 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info