157427
54
Zoom out
Zoom in
Previous page
1/64
Next page
COMPACT HIFI SYSTEM
NV-500
NV-600
This instruction manual is used to describe multiple models listed above.
Model availability and features (functions) may differ depending on the country
and sales area.
INSTRUCTION MANUAL
KENWOOD CORPORATION
B60-4290-00
DIGITAL AUDIO
COMPACT
TEXT
EN
2
Preparation section
MONITOR
OUT
REC OUT PLAY IN PLAY IN
VIDEO 1
VIDEO 1
AUDIO
REC
OUT
PLAY
IN
PLAY
IN
FM
75
GND AM
VIDEO 1
AC 110–
120V
VIDEO 2
VIDEO 2
L
R
ANTENNA
DIGITAL
OUT
OPTICAL
AC 220–
240V
AC 110–
120V
AC 220–
240V
+
-
+
-
FRONT
SPEAKERS
(6 - 16)
SUPER
WOOFER
PRE OUT
LR
AC 110
120V
AC 220
240V
AC 110
120V
AC 220
240V
Before applying power
Units are designed for operation as follows.
U.S.A. and Canada ............................................ AC 120 V only
Australia ............................................................. AC 240 V only
The marking is located on the rear panel and says that the
component uses laser beams that have been classified as
Class 1. It means that the unit is utilizing laser beams that are
of a weaker class. There is no danger of hazardous radiation
outside the unit.
CLASS 1
LASER PRODUCT
The marking of products using lasers
(Except for some areas)
Caution : Read this page carefully to ensure safe operation.
For the United Kingdom
Factory fitted moulded mains plug
1. The mains plug contains a fuse. For replacement, use only
a 13-Amp ASTA-approved (BS1362) fuse.
2. The fuse cover must be refitted when replacing the fuse in
the moulded plug.
3. Do not cut off the mains plug from this equipment. If the
plug fitted is not suitable for the power points in your home
or the cable is too short to reach a power point, then obtain
an appropriate safety approved extension lead or adapter,
or consult your dealer.
If nonetheless the mains plug is cut off, remove the fuse
and dispose of the plug immediately, to avoid a possible
shock hazard by inadvertent connection to the mains sup-
ply.
IMPORTANT:The wires in the mains lead are coloured in ac-
cordance with the following code:
Blue : Neutral
Brown : Live
Do not connect those leads to the earth terminal of a three-
pin plug.
Europe and U.K. ................................................. AC 230 V only
*Other countries...........AC 110-120 / 220-240 V switchable
*AC voltage selection
The AC voltage selector switches on the rear panel are set to
the voltage that prevails in the area to which the unit is shipped.
Before connecting the power cord to your AC outlet, make
sure that the setting position of this switch matches your line
voltage. If not, it must be set to your voltage in accordance
with the following direction.
AC voltage selector switch
Move switch levers to match your line volt-
age with a small screwdriver or other
pointed tool.
Note:
Our warranty does not cover damage caused by excessive
line voltage due to improper setting of the AC voltage selec-
tor switch.
Safety precautions
WARNING : TO PREVENT FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE
TO RAIN OR MOISTURE.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVIC-
ING TO QUALIFIED SERVICE PERSONNEL.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
THE LIGHTNING FLASH WITH ARROWHEAD SYMBOL, WITHIN AN EQUILATERAL TRIANGLE,
IS INTENDED TO ALERT THE USER TO THE PRESENCE OF UNINSULATED “DANGEROUS VOLT-
AGE” WITHIN THE PRODUCT’S ENCLOSURE THAT MAY BE OF SUFFICIENT MAGNITUDE TO
CONSTITUTE A RISK OF ELECTRIC SHOCK TO PERSONS.
THE EXCLAMATION POINT WITHIN AN EQUILATERAL TRIANGLE IS INTENDED TO ALERT THE
USER TO THE PRESENCE OF IMPORTANT OPERATING AND MAINTENANCE (SERVICING) IN-
STRUCTIONS IN THE LITERATURE ACCOMPANYING THE APPLIANCE.
CAUTION
3
Preparation section
Contents
Before applying power............................................ 2
Safety precautions ........................................................... 2
IMPORTANT SAFEGUARDS ..................................... 4
Special features .................................................................6
In regard to demonstration...............................................6
Accessories ........................................................................6
System connection ......................................................... 7
AM loop antenna connection ..........................................7
FM antenna connection ....................................................7
Connection of the speaker system ................................8
Connection of Other Accessories ...................................9
CHANNEL SPACE setting ............................................. 10
Controls and indicators................................................ 11
Operation of remote control unit................................12
Basic configuration of the remote control menu.......13
Selecting an input using the CURSOR key..................13
Clock adjustment .......................................................... 14
Let's put out some sound ............................................. 16
Basic use method.............................................................16
Receiving broadcast station ..........................................18
To receive a station that has not been preset ............19
Collective presetting of stations
(auto preset)
(Except for Europe and U.K.)
Presetting R.D.S. stations
(RDS auto memory for Europe and U.K. ) .........................................
20
One-by-one presetting
(manual preset).................................
21
Playback of CD .................................................................22
In regard to CD-TEXT .......................................................23
Playback of tape...............................................................24
Selecting Dolby NR..........................................................25
Selecting the reverse mode ...........................................25
Let's recording............................................................... 26
Recording on TAPE ..........................................................26
CD synchronized recording............................................27
Caution : Read the pages marked carefully to ensure safe operation.
Before applying power
Knowledge section
Basic section
Preparation section Application section
R.D.S.
(Radio Data System) (for Europe and U.K.) ............................
28
Searching for a desired program type
(PTY search)......
29
To be able to listen to the desired information
at any time (EON)..............................................................30
Playback of CD .............................................................. 32
Listening in the desired sequence
(program playback) ......
32
Repeated playback ..........................................................34
Listening to an unexpected title sequence
(random playback) ...........................................................35
Convenient Recording Methods ................................. 36
Selection of the Recording Type ...................................36
Recording an entire CD onto tape
(CD direct recording) ..........................................................................
37
Recording every desired track in CD onto tape
(CD one-track recording) ....................................................................
38
Recording desired CD tracks in a desired order
onto tape
(CD program recording) ................................................
39
Tone control and sound field effect adjustment...... 40
Adjusting the external input level ................................40
Adjusting the subwoofer output level .........................40
Bass Boost and tone control..........................................41
Dolby Virtual setting........................................................42
DSP mode setting .............................................................43
Timer operation ............................................................. 44
Setting the O.T.T................................................................44
Setting the timer playback .............................................45
Sleep Timer (Sleep) .........................................................46
Timer recording ................................................................47
Checking the time information display of CD .......... 48
Adjusting the display contrast.................................... 49
Remote control of external components .................. 50
Important Items.............................................................. 54
Maintenance .....................................................................54
Reference ..........................................................................54
Disc handling precautions .............................................55
Notes on cassette tape ...................................................55
In case of difficulty ................................................................57
INDEX .............................................................................. 60
Specifications................................................................ 62
4
Preparation section
Caution : Read this page carefully to ensure
safe operation.
IMPORTANT SAFEGUARDS
6. Temperature – The appliance may not function
properly if used at extremely low, or freezing
temperatures. The ideal ambient temperature is
above +5°C (41°F).
7. Heat – The appliance should be situated away from
heat sources such as radiators, heat registers, stoves,
or other appliances (including amplifiers) that produce
heat.
8. Electric shock – Care should be taken so that objects
do not fall and liquid is not spilled into the enclosure
through openings. If a metal objects, such as a hair
pin or a needle, comes into contact with the inside of
this appliance, a dangerous electric shock may result.
For families with children, never permit children to
put anything, especially metal, inside this appliance.
9. Enclosure removal – Never remove the enclosure.
If the internal parts are touched accidentally, a serious
electric shock might occur.
10.Magnetic fields – Keep the appliance away from
sources of magnetic fields such as TV sets, speaker
systems, radios, motorized toys or magnetized
objects.
11.Cleaning – Unplug this appliance from the wall
outlet before cleaning. Do not use volatile solvents
such as alcohol, paint thinner, gasoline, or benzine,
etc. to clean the cabinet. Use a clean dry cloth.
12.Accessories – Do not place this appliance on an unstable
cart, stand, tripod, bracket, or table. The appliance may fall,
causing serious injury to a child or adult, and serious
damage to the appliance. Use only with a cart, stand,
tripod, bracket, or table recommended by the manufacturer,
or sold with the appliance. Any mounting of the appliance
should follow the manufacturer’s instructions, and should
use a mounting accessory recommended by the
manufacturer. An appliance and cart combination should
be moved with care. Quick stops, excessive force, and
uneven surfaces may cause the appliance and cart
combination to overturn.
Please read all of the safety and operating instructions
before operating this appliance. Adhere to all warnings on
the appliance and in the instruction manual. Follow all the
safety and operating instructions. These safety and
operating instructions should be retained for future
reference.
1. Power sources The appliance should be connected to
a power supply only of the type described in the instruction
manual or as marked on the appliance. If you are not sure
of the type of power supply to your home, consult your
appliance dealer or local power company. For appliances
intended to operate from battery power, or other sources,
refer to the instruction manual.
2. Power-cord protection – Power-supply cords should
be routed so that they are not likely to be walked on
or pinched by items placed upon or against them,
pay particular attention to cords at plugs, convenience
receptacles, and the point where they exit from the
appliance.
3.
CAUTION – Polarization This appliance may
be equipped with a polarized alternating-current line plug (a
plug having one blade wider than the other). This plug will
fit into the power outlet only one way. This is a safety
feature. If you are unable to insert the plug fully into the
outlet, try reversing the plug. If the plug should still fail to
fit, contact your electrician to replace your obsolete outlet.
Do not defeat the safety purpose of the polarized plug.
4. Ventilation Slots and openings in the cabinet are
provided for ventilation and to ensure reliable operation of
the appliance and to protect it from overheating, and these
openings must not be blocked or covered. The appliance
should be situated so that its location or position does not
interfere with its proper ventilation.
To maintain good ventilation, do not put records or a table-
cloth on the appliance. Place the appliance at least 10 cm
away from the walls.
Do not use the appliance on a bed, sofa, rug or similar
surface that may block the ventilation openings. This
appliance should not be placed in a built-in installation such
as a bookcase or rack unless proper ventilation is provided
or the manufacturer’s instructions have been adhered to.
5. Water and moisture – The appliance should not be
used near water - for example, near a bathtub,
washbowl, kitchen sink, laundry tub, in a wet
basement, or near a swimming pool, etc.
Never pull or stretch
the cord.
5
Preparation section
13.Lightning For added protection for this appliance during
a lightning storm, or when it is left unattended and unused
for long periods of time, unplug it from the wall outlet and
disconnect the antenna or cable system. This will prevent
damage to the appliance due to lightning and power-line
surges.
14.Abnormal smell – If an abnormal smell or smoke is
detected, immediately turn the power OFF and unplug
the appliance from the wall outlet. Contact your dealer or
nearest service center.
15.Damage requiring service – The appliance should
be serviced by qualified service personnel when:
A. The power-supply cord or the plug has been
damaged.
B. Objects have fallen, or liquid has been spilled into
the appliance.
C. The appliance has been exposed to rain or water.
D. The appliance does not appear to operate normally
by following the instruction manual. Adjust only those
controls that are covered by the instruction manual as an
improper adjustment of other controls may result in damage
and will often require extensive work by a qualified
technician to restore the appliance to its normal operation.
E. The appliance has been dropped, or the enclosure
damaged.
F. The appliance exhibits a marked change in performance.
16.Servicing – The user should not attempt to service
the appliance beyond that described in the instruction
manual. All other servicing should be referred to
qualified service personnel.
17.Outdoor antenna grounding – If an outside antenna
is connected to the appliance, be sure the antenna
system is grounded so as to provide some protection
against voltage surges and built up static charges.
Article 810 of the National Electrical Code ANSI/
NFPA 70, provides information with respect to proper
grounding of the mast and supporting structure,
grounding of the lead-in wire to an antenna discharge
unit, size of grounding conductors, location of antenna
discharge unit, connection to grounding electrodes,
and requirements for the grounding electrode. See
Figure.
18.Power lines An outside antenna system should not be
located in the vicinity of overhead power lines or other
electric light or power circuits, or where it can fall into such
power lines or circuits. When installing an outside antenna
system, extreme care should be taken to keep from
touching such power lines or circuits as contact with them
might be fatal.
19.AC outlets – Do not connect other audio equipment
with a power consumption larger than that specified
to the AC outlet on the rear panel. Never connect
other electrical appliances, such as an iron or toaster,
to it to prevent fire or electric shock.
20. Overloading – Do not overload wall outlets, extension
cords, or integral convenience receptacles as this can
result in a risk of fire or electric shock.
21. Attachment – Do not use attachments not recommended
by the appliance manufacturer as they may cause hazards.
22. Replacement parts – When replacement parts are required,
be sure the service technician has used replacement parts
specified by the manufacturer or have the same
characteristics as the original parts. Unauthorized
substitutions may result in fire, electric shock, or other
hazards.
23. Safety check – Upon completion of any service or repairs
to this appliance, ask the service technician to perform
safety checks to determine that the appliance is in proper
operating condition.
Notes:
1. Item 3 is not required except for grounded or polarized equipment.
2. Item 17 and 18 are not required except for units provided with
antenna terminals.
3. Item 17 complies with UL in the U.S.A.
EXAMPLE OF ANTENNA GROUNDING AS PER
NATIONAL ELECTRICAL CODE
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
NEC – NATIONAL ELECTRICAL CODE
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
ANTENNA
LEAD IN WIRE
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
GROUND CLAMP
ELECTRIC
SERVICE
EQUIPMENT
GROUND
CLAMPS
Caution : Read this page carefully to ensure safe operation.
IMPORTANT SAFEGUARDS
6
Preparation section
Special features
Unpacking
Unpack the unit carefully and make sure that all accessories are put aside so they will not be lost.
Examine the unit for any possibility of shipping damage. If your unit is damaged or fails to operate, notify your dealer immediately.
If your unit was shipped to you directly, notify the shipping company without delay. Only the consignee (the person or company
receiving the unit) can file a claim against the carrier for shipping damage.
We recommend that you retain the original carton and packing materials for use should you transport or ship the unit in the future.
Keep this manual handy for future reference.
In regard to demonstration
This unit is equipped with a demonstra-
tion function (only display). The demon-
stration consists of sequential change of
display and indicators showing the op-
erations, but the audio itself does not
change. The demonstration function can
be cancelled as follows.
Before applying power
Accessories
FM indoor antenna (1) Loop antenna (1) Remote control unit (1)
Batteries (R6/AA) (6)
Please confirm that the following accessories are present.
*AC plug adaptor (1)
*Use to adapt the plug on the power
cord to the shape of the wall outlet.
(Accessory only for regions where
use is necessary.)
To switch over the demonstration:
Switch power ON before the following
operation.
To cancel the demonstration mode:
Press the CONFIRM/DEMO key.
To start the demonstration mode:
Press and hold the CONFIRM/
DEMO key for about 2 seconds.
÷ The setting is remembered even when the power is switched off.
÷ This operates automatically when a power failure has occurred or the plug of the power cable has been pulled while
the power was ON. Cancellation is possible by pressing the key during the demonstration.
CONFIRM
/DEMO
Bidirectional remote control unit with play mode display at hand
The bidirectional remote uses a large-sized display for easy-to-see, simple operations.
Dolby Virtual Surround
The Dolby Virtual Surround function provides realistic surround effect through only two
loudspeakers.
High output power with large headroom
High, 100 W + 100 W power amplifier enables powerful musical reproduction. (NV-500)
Leave the remote control unit attached to
the main unit during operation. @
7
Preparation section
System connection
AM loop antenna connection
The supplied antenna is for indoor use. Place
it as far as possible from the main system,
TV set, speaker cords and power cord, and
set it to a direction which provides the best
reception.
FM indoor antenna connection
The accessory antenna is for temporary in-
door use only. For stable signal reception
we recommend using an outdoor antenna.
Remove the indoor antenna if you connect
one outdoors.
123
AM loop antenna connection
FM antenna connection
1 Connect to the antenna terminal.
2 Locate the position providing good
reception condition.
3 Fix the antenna.
FM outdoor antenna
Lead the 75 coaxial cable connected to
the FM outdoor antenna into the room and
connect it to the FM 75 terminal.
Antenna adapter
(Commercially-
available)
+
-
+
-
MONITOR
OUT
REC OUT PLAY IN PLAY IN
VIDEO 1
VIDEO
AUDIO
REC
OUT
FRONT
SPEAKERS
(6 - 16)
SUBWOOFER
(4 - 16)
PLAY
IN
PLAY
IN
FM
75
GND AM
VIDEO 1
AC 110–
120V
VIDEO 2
VIDEO 2
L
R
LR
ANTENNA
DIGITAL
OUT
OPTICAL
AC 220–
240V
AC 110–
120V
AC 220–
240V
FM
75
GND AM
ANTENNA
+
-
+
-
MONITOR
OUT
REC OUT PLAY IN PLAY IN
VIDEO 1
VIDEO 1
AUDIO
REC
OUT
FRONT
SPEAKERS
(6 - 16)
SUBWOOFER
(4 - 16)
PLAY
IN
PLAY
IN
FM
75
GND AM
VIDEO 1
AC 110–
120V
VIDEO 2
VIDEO 2
L
R
LR
ANTENNA
DIGITAL
OUT
OPTICAL
AC 220–
240V
AC 110–
120V
AC 220–
240V
+
-
+
-
MONITOR
OUT
REC OUT PLAY IN PLAY IN
VIDEO 1
VIDEO
AUDIO
REC
OUT
FRONT
SPEAKERS
(6 - 16)
SUBWOOFER
(4 - 16)
PLAY
IN
PLAY
IN
FM
75
GND AM
VIDEO 1
AC 110–
120V
VIDEO 2
VIDEO 2
L
R
LR
ANTENNA
DIGITAL
OUT
OPTICAL
AC 220–
240V
AC 110–
120V
AC 220–
240V
FM
75
GND AM
ANTENNA
FM
75
GND AM
ANTENNA
POWER cord
TO WALL AC
OUTLET
8
Preparation section
Connection of the speaker system
NV-600
+
-
+
-
MONITOR
OUT
REC OUT PLAY IN PLAY IN
VIDEO 1
VIDEO
AUDIO
REC
OUT
FRONT
SPEAKERS
(6 - 16)
SUBWOOFER
(4 - 16)
PLAY
IN
PLAY
IN
FM
75
GND AM
VIDEO 1
AC 110–
120V
VIDEO 2
VIDEO 2
L
R
LR
ANTENNA
DIGITAL
OUT
OPTICAL
AC 220–
240V
AC 110–
120V
AC 220–
240V
+
-
+
-
R L
FRONT
SPEAKERS
(6 - 16)
SUBWOOFER
(6 - 16)
Never short-circuit the + and – speaker cords.
If the left and right speakers are connected inversely or if the speaker cords are connected with reversed polarity, the sound
becomes unnatural with ambiguous acoustic image positioning. Be sure to connect the speakers and speaker cords correctly.
NV-500
MONITOR
OUT
REC OUT PLAY IN PLAY IN
VIDEO 1
VIDEO
AUDIO
REC
OUT
PLAY
IN
PLAY
IN
FM
75
GND AM
VIDEO 1
AC 110–
120V
VIDEO 2
VIDEO 2
L
R
ANTENNA
DIGITAL
OUT
OPTICAL
AC 220–
240V
AC 110–
120V
AC 220–
240V
+
-
+
-
FRONT
SPEAKERS
(6 - 16)
SUPER
WOOFER
PRE OUT
LR
+
-
+
-
R L
FRONT
SPEAKER
(6 - 16)
B
a
s
s
r
e
f
l
e
x
s
p
e
a
k
e
r
s
y
s
t
e
m
B
a
s
s
r
e
f
l
e
x
s
p
e
a
k
e
r
s
y
s
t
e
m
Do not plug the power cord into the power outlet until
all of the required connections have been made.
Malfunction of microcomputer
If operation is not possible or erroneous display appears
even though all connections have been made properly, re-
set the microcomputer referring to “In case of difficulty”. ¤
U
12 3 12 3
Main Unit
Twist
Speaker
system
Twist
Speakers front view
Speakers front view
Connect only provided main unit.
Connect only provided main unit.
Speaker (left)
Speaker (right)
Speaker (left)
Speaker (right)
System connection
9
Preparation section
Connection of Other Accessories
(Commercially Available Parts)
MONITOR
OUT
REC OUT PLAY IN PLAY IN
VIDEO 1
VIDEO
AUDIO
REC
OUT
PLAY
IN
PLAY
IN
FM
75
GND AM
VIDEO 1
AC 110–
120V
VIDEO 2
VIDEO 2
L
R
ANTENNA
DIGITAL
OUT
OPTICAL
AC 220–
240V
AC 110–
120V
AC 220–
240V
+
-
+
-
FRONT
SPEAKERS
(6 - 16)
SUPER
WOOFER
PRE OUT
LR
MONITOR
OUT
REC OUT PLAY IN PLAY IN
VIDEO 1
VIDEO
AUDIO
REC
OUT
PLAY
IN
PLAY
IN
VIDEO 1 VIDEO 2
VIDEO 2
L
R
SUPER
WOOFER
PRE OUT
DIGITAL
OUT
OPTICAL
DIGITAL OUT jack
(OPTICAL)
If necessary, remove the
cap and plug the optical-
fiber cable (optional)
Cap
Optical-fiber
cable
Optical-fiber cable
MD recorder or DAT etc.
Monitor TV
Video Input
Video deck
DVD player or LD player
Audio output
Video output
Video output
Video input
Audio input
Audio output
Powered subwoofer
Only for NV-500
System connection
CAUTION
Be sure to adhere followings. Or proper ventilation will be blocked causing damage or fire hazard.
÷ Do not place any objects impairing heat radiation onto the top of unit.
For U.S.A. and Canada
CAUTION
Be sure to adhere followings. Or proper ventilation will be blocked causing damage or fire hazard.
÷ Do not place any objects impairing heat radiation onto the top of unit.
÷ Leave a space around the unit (from the largest outside dimension including projection) equal or greater
than, shown below.
Back panel : 10 cm
For other countries
10
Preparation section
The space between radio channels has been set to the one
that prevails in the area to which the system is shipped.
However, if the current channel space setting does not
match the setting in the area where the system is to be used,
for instance when you move from area 1 or area 2 shown in
the following table or vice versa, proper reception of AM/FM
broadcasts cannot be expected. In this case, change the
channel space setting in accordance with your area by refer-
ring to the following table.
CHANNEL SPACE setting
(Except for the U.S.A., Canada, U.K., Europe and Australia)
CHANNEL
SPACE freq.
Area
1
2
USA, Canada and South
American countries
Other countries
FM : 100 kHz
AM: 10 kHz
FM : 50 kHz
AM: 9 kHz
CURSOR
SET
STOP
1
Attach the remote control
unit to the main unit
@
2
Switching the power ON
3
Select the TUNER input.
4
Press and hold the STOP (
7
)
key for about 2 seconds.
5
Select the message to be
displayed, "FM 100kHz" or
"FM 50kHz".
STANDBY/TIMER
ON/STANDBY
CURSOR
SET
TV
VIDEO1
VIDEO2
CD
TUNER
TAPE
FUNCTION
7
INPUT
÷ The setting is remembered even when the power is
switched off.
11
Preparation section
Controls and indicators
CD
CD
6
TAPE
2 3
MUTE
TUNER TAPE MUTE
ACTIVE
TUNER/BAND
STOP
ON/STANDBY
STANDBY/TIMER
VOLUME
STEREO
0
PHONES
PUSH OPEN
1
1
2
3
4
5
6
7
8
9
0
!
POWER
ON/STANDBY
STANDBY/TIMER
@
#
TV
VIDEO1
VIDEO2
CD
TUNER
TAPE
FUNCTION
^
%$
VOLUME CONTROL
CLOCK
/LIGHT
MUTE
CONFIRM
/DEMO
HOME
IR ON/STANDBY
BAND
INPUT
DIRECTION
SET ENTER
REC
– P.CALL –
CURSOR
6
7
¢4
¡1
IR POWER
&
*
(
)
¡ ™ £
¢
∞
§
¶
•
ª
⁄¤ ¤ º
1 POWER/ON/STANDBY key $
(for U.S.A and CANADA)
ON/STANDBY (
) key $
(for other countries)
STANDBY/TIMER indicator&
2 (CD) open/close (0) key
3 CD tray
4 PHONES jack &
5 Remote control sensor @
6 Cassette holder ¢
Press the area marked “PUSH
OPEN” to load or eject a tape.
7 Remote control signal trans-
mitter @
8 STOP key £
9 VOLUME keys ^
0 Input selector keys ^
MUTE key &
! Input indicators
@ Communication indicator
Blinks during communication
with the remote control unit.
# ACTIVE indicator
Lights during CD, MD or tape
playback or tuner reception.
$ Selector display/icon
Shows the operations selected
with the remote control.
% Menu/recording, editing selec-
tion display
Shows the selection menu, type
of recording or editing, etc.
^ Input selection display
Shows the status selected on
the main unit or the input func-
tion selected with the remote
control unit.
& VOLUME CONTROL keys ^
* CLOCK/LIGHT key $
( CONFIRM/DEMO key #
) HOME key #
¡ MUTE key &
P.CALL/4 , ¢ keys
$*
£ Stop (7) key
¢ INPUT key £
REC key
§ DIRECTION key ¢
SET key #
ENTER key ¤
ª CURSOR keys #
º 6/BAND key *
Display
¤ IR POWER (
) key #
(for U.S.A and CANADA)
IR ON/STANDBY (
) key #
(for other countries)
*The displayed information is variable depending on areas.
12
Preparation section
Operation of remote control unit
3 Close the cover.1 Remove the cover. 2 Insert batteries.
÷ Insert six R6 (“AA”-size) batteries
following the polarity indications.
Loading batteries
30°
30°
30°
30°
CLOCK
/LIGHT
Operation
÷ When pressing more than one remote control keys
successively, press the keys securely by leaving an
interval of 1 second or more between keys.
After plugging the power cord of this unit, press
the
key of the remote control unit to turn the
system ON. When the system is turned ON, press
the key of the function to be operated.
Operating range
(approx.)
Remote sensor
Remote control
signal transmitter
6 m
6 m
When the remote control unit is attached to the
main unit, the power can be switched ON/OFF
only using the POWER (
) key on the main unit.
To light the back light:
(The back light is permanently on when the remote control unit is
attached to the main unit with power on.)
Press and hold the CLOCK/LIGHT key for
about 2 seconds.
When the remote control unit is detached from
the main unit, it is recommended to leave the
display back light off in normal condition in
order to save the battery power.
NotesNotes
Notes
1.The provided batteries are intended for use in operation checking, and their service life may be short.
2.When the batteries are nearly exhausted, "Low Battery" appears and the remote controllable distance decreases.
In this case, replace all of the 6 batteries with new ones. (It is recommended to replace batteries with alkaline
batteries.)
3.If direct sunlight or the light of a high- frequency fluorescent lamp (inverter type, etc.) is incident to the remote
sensor, malfunction may occur. In such a case, change the installation position to avoid malfunction.
Attaching/detaching the remote control unit
1 Open the terminal block
cover of the main unit.
Terminal block cover
2 To attach the remote control
unit to the main unit:
Attach by slightly
tilting the remote
control unit.
3 To detach the remote control unit
from the main unit:
Remove in the
upper direction by
slightly tilting the
remote control unit.
To reset the remote control unit
÷ Do not touch the terminals.
÷ Be sure to close the cover when
the remote control unit is detached.
The remote control unit may mal-
function due to strong external noise,
etc. In this case, remove all batter-
ies and push the reset button with a
thin-tipped object. This resets the mi-
crocomputer to the initial condition.
Reset button
Model : GRC-NV501 (for U.S.A. and Canada)
Model : GRC-NV502 (for Europe and U.K.)
Model : GRC-NV503 (for other countries)
Infrared ray system
13
Preparation section
IR ON/STANDBY
CURSOR
SET
TV
VIDEO1
VIDEO2
CD
TUNER
TAPE
FUNCTION
TV
VIDEO1
VIDEO2
CD
TUNER
TAPE
FUNCTION
HOME
SET
SET
CURSOR
CURSOR
SET
TV
VIDEO1
VIDEO2
CD
TUNER
TAPE
FUNCTION
TV
VIDEO1
VIDEO2
CD
TUNER
TAPE
FUNCTION
j[˚
Basic configuration of the remote control menu
The provided remote control unit has a large LCD
screen to allow interactive remote control operation.
A variety of operations can be remote controlled by
performing selection in the menu screens.
Screen configuration
(Example when selecting the stereo mode of the
tuner)
Basic screen
Shows the selected input,
recording condition, etc.
Operation of remote control unit
Input selected
on the main unit
Press the SET key to
go to a menu screen.
Press the CURSOR keys to move
up and down.
The selected items can be re-
mote controlled. The information
related to this item is shown on
the display.
Indicates the pres-
ence of next page
Indicates the presence
of previous page
Press the CURSOR keys
to select a menu item.
Press the SET key to go to
the next screen.
Select an item with the CURSOR key
and press the SET key to set the
selection.
Menu screen Selection screen
:Item being selected with the CURSOR keys
:Item that can be selected
:Item that cannot be selected under the current
condition
How to use the HOME key
Pressing the HOME key in the mid-
dle of selection returns to the basic
screen.
How to use the CONFIRM/DEMO key
The remote control unit displays information while holding
communications with the main unit. Pressing the CONFIRM/
DEMO key allows you to reconfirm the current situation.
Selecting an input using the CURSOR key
It is usually the INPUT key that is used to select an input such as CD, TAPE or TUNER from the remote control
unit. However, the input to be recorded can also be selected using the CURSOR keys. Use the CURSOR key
as described below.
1
Switch power ON.
2
Press one of the CURSOR
keys to select an input.
3
Press the SET key to set the
selection.
4
Press the BAND key.
(The input is switched as
selected and the source
starts to play.)
IR POWER
or
14
Preparation section
CLOCK
/LIGHT
SET
¢4
–P.CALL–
SET
CLOCK
4, ¢
SET
STANDBY/TIMER
CLOCK
/LIGHT
Clock adjustment
Adjust the clock before setting the timer.
After plugging the AC cord into a power
outlet, set the time of the day as described
below.
ON/STANDBY
1. Switch power ON.
If a CD or cassette has been loaded in the unit, simply pressing the play
key turns power ON and starts playback automatically.
To stop the playback, press the 7 key.
2. Display the Clock display.
3. Display the Clock Adjust
screen.
The displayed time of the day blinks
when the clock has not been adjusted.
4. Adjust the time.
5. Set the time.
After setting the correct time of the day, press the SET key.
To display the time
Press the CLOCK/LIGHT key. The LCD display shows
the time for abut 5 seconds then returns to the previ-
ous display.
÷ In other areas than the UK, Europe and
Australia, the clock shows the time of
the day in the 12-hour system.
÷ The previous display will reappear if no
operation is performed for about 5
seconds.
15
Preparation section
16
Basic section
11
22
33
11
22
33
STANDBY/TIMER
11
CD
6
TUNER
/BAND MUTE
TAPE
™£
22
VOLUME
33
1. Switch power ON.
If a CD or cassette has been loaded in the unit, simply pressing the
play key (6) turns power ON and starts playback automatically.
2. Select the desired source.
÷ If CD or TAPE is selected and a disc or tape has already been loaded
in the main unit, its playback starts now.
3. Volume adjustment.
The volume
decreases
The volume
increases
Let's put out some sound
Basic use method
17
Basic section
PHONES
INPUT
ENTER
¢4
–P.CALL–
VIDEO2
CD
TUNER
TAPE
FUNCTION
MUTE
CURSOR
SET
Muting the sound temporarily
÷ Press again to resume the original volume.
÷ This is also cancelled when the volume is changed.
MUTE
Listening through headphones
Insert the headphone plug into the “PHONES”
jack.
÷ Headphones with a stereo mini plug can be connected.
÷ The sounds from all speakers are cut off.
Standby mode
While the standby indicator of the unit is lit in red or
amber, a small amount of current is flowing into the
unit’s internal circuitry to back up the memory. This
condition is referred to as the standby mode of the unit.
While the unit is in the standby mode, it can be turned
ON from the remote control unit.
One-touch operation
With this feature, when the play key for the CD or TAPE
input or the BAND key for the TUNER input is pressed,
the power of the unit is switched ON automatically.
÷ When the CD or TAPE input selected while a disc or
tape has already been loaded, its playback also starts
automatically.
STANDBY/TIMER indicator
When power is STANDBY : Lights in red.
When power is ON : Lights in green.
During timer standby : Lights in amber.
When timer standby is initiated without set-
ting the current time of the day :
Blinks in green.
When the protection circuitry is activated :
Blinks in red. (In this case, unplug the
power cord and ensure that the
speaker cords are not short-circuited.)
When using the remote control unit, each press of
the INPUT key switches the input as shown below.
1 Press INPUT key
1 VIDEO1
2 VIDEO2
3 CD
4 TUNER
5 TAPE
2 Press 6(BAND) key
Adjusting the left and right volume balance
1
Display the "Function" menu.
2
Select "Balance".
3
Adjusting the left and right
volume balance
4
Set the adjusted balance.
The right
volume is
decreased.
The left
volume is
decreased.
Let's put out some sound
When the display of the remote control
unit shows nothing, information can be
displayed by pressing the HOME key.
CURSOR
SET
18
Basic section
TUNER
/BAND
11
¢4
–P.CALL–
11
22
TUNER
/BAND
22
33
33
11
22
1. Select the TUNER input.
2. Select the broadcast band.
Each press changes the band.
1FM
2AM
or
1FM
2MW
3LW
3. Select a station.
It is recommended to preset radio stations in advance.
Every time the key (4 or ¢) is pressed, the preset stations are
switched over as follows.
Press ¢ for the order of 1=2=3 ... 38=39=40=1...
Press 4 for the order of 40=39=38 ... 3=2=1=40...
When the key is held depressed for more than 2 seconds... \
Seek of preset stations starts and stops automatically when
a station is detected.
Main unit
Main unit
Remote control only
Receiving broadcast station
Let's put out some sound
19
Basic section
INPUT
Remote control
Remote control
6
BAND
1 VIDEO1
2 VIDEO2
3 CD
4 TUNER
5 TAPE
Frequency display
preset number
display
Switching between stereo tuning and monaural tuning
Use the monaural tuning mode when the radio wave is weak and noisy.
1
With the TUNER input
selected, press the SET
key to display the Tuner
menu.
SET
2
Select "Stereo/Mono".
3
Select "Stereo" or "Mono"
and press the SET key to
set the selection.
To receive a station that has not been preset
1
Select the TUNER input and
the receiving band.
2
Press the SET key to display
the Tuner menu.
3
Select the “Direct Tuning”
Select with the CURSOR
key and press the SET key.
4
Select the receiving fre-
quency.
Select the frequency with one of
the P.CALL keys and press the
SET key to set the selection.
6
BAND
INPUT
CURSOR
SET
CURSOR
SET
SET
CURSOR
SET
¢4
–P.CALL–
SET
Let's put out some sound
20
Basic section
INPUT
TV
VIDEO1
VIDEO2
CD
TUNER
TAPE
FUNCTION
Let's put out some sound
A maximum of 40 stations will be preset.
When there are many stations and the intended
station has not been preset, please also use
“One-by-one presetting (manual preset)”.
1
Select the TUNER input.
2
Display the "Tuner" menu.
3
Select "Auto Preset" or
"Auto Memory".
1 VIDEO1
2 VIDEO2
3 CD
4 TUNER
5 TAPE
CURSOR
SET
Collective presetting of stations
(auto preset) (Except for Europe and U.K.)
Presetting R.D.S. stations (RDS auto memory for Europe and U.K. )
÷ The displayed information is variable depending on
areas.
÷ It takes a certain period of time before presetting
completes.
SET
CURSOR
SET
21
Basic section
Desired radio stations can be selected and
preset one by one. (Up to 40 stations can be
preset in memory.)
1
Receive a desired station
in advance.
("To receive a station that
has not been preset")
(
2
With the TUNER input
selected, press the SET
key to display the Tuner
menu.
3
Select "Manual Memory"
with the CURSOR key and
press the SET key.
4
Select one of preset
numbers 1 to 40.
CURSOR
SET
One-by-one presetting
(manual preset)
To preset another station, repeat steps 1 to
4 above.
Let's put out some sound
SET
CURSOR
SET
CURSOR
SET
22
Basic section
11
22
22
0
11
CD
6
T
/
22
TV
VIDEO1
VIDEO2
CD
TUNER
TAPE
FUNCTION
1. Load a disc.
1 Open the CD tray.
2 Place a disc.
3 Close the CD tray.
2. Start playback.
The label side must
be on top.
Display when the remote
control unit is attached to
the main unit
Display when the remote
control unit is detached
from the main unit
Track No. being played
Displayed with a CD
TEXT-compatible
disc. £
Elapsed play time of the
track being played
Track No. being played
Display during playback
(During stop: "Stop".
During pause: "Pause")
When a CD disc has been loaded in the CD tray in
advance, simply pressing the CD 6 key on the
main unit turns power ON and starts playback
automatically.
Playback of CD
Skipping
tracks
Start
playback/
to pause
playback
To stop playback
INPUT
Start
playback/
to pause
playback
Let's put out some sound
TV
VIDEO1
VIDEO2
CD
TUNER
TAPE
FUNCTION
STOP
23
Basic section
6
BAND
CD
6
TUNE
R
/BAN
D
STOP
0
Skipping tracks
To skip backward To skip forward
÷ The track in the direction of the key pressed is
skipped, and the selected track will be played from the
beginning.
÷ When the 4 key is pressed once during playback, the
track being played will be played from the beginning.
When a key is held depressed:
÷ The track is fast forwarded or reversed.
÷ Normal playback resumes from the position
where the key is released.
÷ Each press pauses and plays the CD alternately.
To pause playback
To stop playback
To eject the disc
÷ The CD tray opens.
1 Press the INPUT key to select the CD input.
1 VIDEO1
2 VIDEO2
3 CD
4 TUNER
5 TAPE
2 Press 6(BAND) key
Remote control operation...
In regard to CD-TEXT
When discs conforming to CD-TEXT are played with
this unit, the text information recorded on the CD
(disc name or titles) is displayed automatically.
During stop: The disc title is displayed.
During playback: The title of the track being
played is displayed.
CD-TEXT display
When the remote control unit is attached to the
main unit: Characters are scrolled (moved) from
the right to the left.
When the remote control unit is detached from the
main unit: Only the first 10 characters are displayed.
Let's put out some sound
¢4
–P.CALL–
INPUT
24
Basic section
PUSH OPEN
TAPE
™£
22
22
STOP
A
11
22
11
DIRECTION
Playback of tape
If you load a tape in the cassette deck in advance
while the power is off. pressing the TAPE key
turns power on automatically and starts the tape
playback.
CURSOR
INPUT
Fast forwarding
/rewinding or
skipping tape
To stop playback
1. Load a cassette tape.
1 Open the cassette holder.
2 Insert a tape and close the
cassette holder
2. Start playback.
During playback, the tape running direction changes each time the
key is pressed.
÷ Be sure to remove tape slack.
÷ Be sure to close the cassette holder completely.
÷ The normal (TYPE I), High (TYPE II) or Metal (TYPE
IV) tape types are detected and set automatically.
Note on the tape transport direction
The direction in which tape advances when playback or
recording is started automatically by the one-touch opera-
tion feature, etc. is indicated by an indicator. The indicated
tape direction it that used when the tape was stopped
last. (To switch the direction, press the DIRECTION key
on the remote control unit.)
To stop playback
÷ Do not take out the cassette tape
until the tape transport has stopped
completely.
The tape counter is set to “0000” when a cassette tape is loaded.
By writing down the counter reading in case you want to interrupt
recording (playback) in the middle of the tape, the memo will be helpful
as a reference for locating the same position when continuing the
recording (playback) the next time. The tape counter figure decrements
during recording or playback of the back side (while the ¤ tape
transport indicator is lit).
To set the tape counter to “0000”, open the cassette holder once.
Then the counter will be reset.
A tip for use of the tape counter
Let's put out some sound
25
Basic section
CURSOR
SET
6
BAND
TV
VIDEO1
VIDEO2
CD
TUNER
TAPE
FUNCTION
Fast forwarding/rewinding or skipping tape
By leaving non-recorded blanks of 4 seconds or
more between each piece of music, desired piece of
music can be selected by skipping others (up to 16
in each of the backward and forward directions).
To rewind tape or skip
music in direction |
To fast forward tape or
skip music in direction \
When the key is pressed during stop
÷ Fast forwarding or rewinding starts.
÷ Press the stop key (7) to stop fast forwarding or rewinding.
When the key is pressed during play
÷ Skipping of music starts.
Caution for cassette tape ejection
÷ Do not attempt to eject the cassette tape until the
tape has been stopped completely by pressing the
stop (7) key. Opening the cassette holder while the
mechanism is running may lead to malfunction.
Should it become impossible to close the cassette
holder, turn power off then on again.
1 Press the INPUT key to select the TAPE input.
1 VIDEO1
2 VIDEO2
3 CD
4 TUNER
5 TAPE
2 Press 6(BAND) key.
Remote control operation...
Displayed when Dolby NR is selected
Reverse mode indicator
tape transport
direction indicator
When the remote control unit is attached
to the main unit: Tape counter
When it is detached from the main unit:
"Stop" for stop, "Play" for playback.
Selecting Dolby NR
Using the Dolby NR in recording allows you to
reduce tape hiss noise. Be sure to set "Dolby NR"
on when playing back a tape recorded with Dolby
NR.
1 Select "TAPE" with the CURSOR key.
2 Display the "TAPE" menu.
3 Select the "Dolby NR" setting mode.
4 Select "On" or "Off" and press the SET
key.
Selecting the reverse mode
The reverse mode determines the mode of auto-
matic reversal of tape at the end of each side.
1 Select "TAPE" with the CURSOR key.
2 Display the "TAPE" menu.
3 Select the "Direction" setting mode.
4 Select one of the following reverse
modes and press the SET key.
1 ”: Playback stops after having
played one side of tape.
2
”: Playback stops after having
played both sides of tape in a
deck.
3
”: Endless playback of both
sides of tape.
Let's put out some sound
¢4
–P.CALL–
INPUT
CURSOR
SET
SET
CURSOR
SET
CURSOR
SET
CURSOR
SET
SET
CURSOR
SET
26
Basic section
INPUT
REC
CURSOR
DIRECTION
SET
PUSH OPEN
DIRECTION
Recording on TAPE
Note that this cassette deck cannot record onto
Metal tapes.
NoteNote
Note
Let's recording
1. Load a cassette tape.
1 Open the cassette holder.
2 Insert a tape and close the
cassette holder
÷ Be sure to remove tape slack.
÷ Be sure to close the cassette holder completely.
÷ The normal (TYPE I) or High (TYPE II) tape types are detected and set auto-
matically.
÷ Use a cassette tape with which the protect tab for accidental erasure pre-
vention is not broken.
T
TUNER (Broadcasts)
VIDEO1
VIDEO2
2. Select the source to be recorded.
To record sound from a CD, use the dedicated
recording function by referring to "CD synchro-
nized recording" () or "Convenient record-
ing methods" ().
The present procedure described the most
general recording method
3. Select the tape transport direction.
÷ When recording is started, the tape is transported in the direction selected in this
step.
÷ Wind the tape to the position where recording is to be started.
To reverse the tape transport direction
1 Select "TAPE" with the CURSOR key.
2 Press the SET key.
3 Press the DIRECTION key to switch the
tape transport direction.
12
3
INPUT
CURSOR
SET
27
Basic section
REC
REC
7
TV
VIDEO1
VIDEO2
CD
TUNER
TAPE
FUNCTION
Pause the recording (A.R.M.)
÷ Press the REC key during recording. It stops after
leaving a non-recorded blank of 4 seconds. (Press the
key again to resume recording.)
Stop the recording
CD synchronized recording
When recording a CD, the playback of the source
and recording of the cassette deck can be synchro-
nized by putting the cassette deck in record-pause
mode. (Sync recording)
1 Put the CD recorder in pause mode.
2 Select the music to be recorded by using the
skip key (4 or ¢). (The tape pauses at the
beginning of the selected music.)
3 Put the cassette deck in record-pause mode.
4 Start playback of the CD. (Sync recording
starts.)
÷ Press the stop key (7) of the CD player to stop
recording.
4. Set the recording condition.
1 Perform steps 2 to 4 of "Selecting the reverse mode" on page 25.
2 Perform steps 2 to 4 of "Selecting Dolby NR" on page 25.
5. Start recording.
Displayed when Dolby NR is selected
Reverse mode indicator
tape transport
direction indicator
When the remote control unit is
attached to the main unit:
Tape counter
When it is detached from the main
unit:"Stop" for stop,
"Play" for playback,
"Rec Pause" for record pause,
"A.R.M." during A.R.M. op-
eration.
Recording indicator
÷ Recording stops automatically when the tape side (s)
to be recorded have been fully recorded.
Let's recording
Check that "Tape" is being displayed,
then press the REC button.
28
Application section
RDS is a system which transmits useful informa-
tion (digital data) for FM broadcasts together with
the broadcast signal. Tuners and receivers de-
signed for RDS reception can extract the informa-
tion from the broadcast signal for use with vari-
ous functions such as automatic display of the
station name.
R.D.S.
(Radio Data System) (for Europe and U.K.)
This unit is equipped with the following functions utilizing RDS data :
PTY (Program Type Identification) Search :
The tuner automatically searches for a station which is
currently broadcasting a specified program type (genre).
PS (Program Service Name) Display :
When an RDS broadcast is received, the station name is
automatically displayed.
EON (Enhanced Other Network) :
When the information to be received is set in advance
and any RDS station in the same network starts broad-
casting of such information, the reception automatically
will be switched to that station.
TV
VIDEO1
VIDEO2
CD
TUNER
TAPE
FUNCTION
RDS, EON, TP indication
Program number
indication
PS or PTY
data indication
Frequency indication
Before using RDS
For reception of RDS stations, the auto presetting function must be used to preset the stations.
With the auto presetting function, RDS stations are preset with priority.
29
Application section
CURSOR
SET
INPUT
SET
1
Select the TUNER input.
2
Display the "Tuner" menu.
3
Select "PTY
✻✻✻
".
4
Select the desired PTY.
CURSOR
INPUT
SET
By specifying the type of program (genre) you
want to listen to, the tuner automatically searches
for a station which is currently broadcasting a
program of the specified type.
Searching for a desired program type (PTY search)
"✻✻✻" shows the currently
selected PTY display.
÷ When an RDS broadcast is received, the program
type is shown on the display. If no PTY data is avail-
able, or if the station is not an RDS station, NONE
is displayed.
R.D.S. (Radio Data System)
TV
VIDEO1
VIDEO2
CD
TUNER
TAPE
FUNCTION
1 VIDEO1
2 VIDEO2
3 CD
4 TUNER
5 TAPE
CURSOR
SET
Preset the RDS stations before setting the PTY
30
Application section
TV
VIDEO1
VIDEO2
CD
TUNER
TAPE
FUNCTION
1 VIDEO1
2 VIDEO2
3 CD
4 TUNER
5 TAPE
CURSOR
INPUT
SET
To be able to listen to the desired information at any time
(EON)
By using the EON function, which manages the information of other stations, listening to desired
information like traffic information or news etc. can be reserved even when it is not being transmitted at
the present. When listening to a station with the “EON” display lit and another station of the same
network starts to broadcast an information program for which a reservation has been made, then that
station will be selected automatically. When the desired information program ends, return is made to the
original program.
1
Select the TUNER input.
2
Display the "Tuner" menu.
3
Select "EON
✻✻✻
".
4
Select the desired EON
mode.
"✻✻✻" shows the currently
selected EON mode display.
Off........................... EON cancelled
TA ...........................Traffic Announcement
NEWS ..................... News
TA & NEWS ........... Traffic Announcement
and News
Select the desired information.
1
R.D.S. (Radio Data System)
CURSOR
SET
INPUT
SET
CURSOR
SET
31
Application section
Receive an RDS station.
2
¢4
–P.CALL–
Select a station where “RDS” and “EON” are lit.
RDS” and “EON” are Lit
Wait for the desired information.
3
CD or TAPE playback may also be started.
As long as the unit is ON, the unit is always ready
for the reception.
÷ When one of the stations of the network of the station
received in 2 starts broadcasting the program contents
selected in 1, that station will be received automatically.
At this time, Tape playback will stop and CD playback will
pause. However, external equipment (VIDEO1/VIDEO2)
will remain as it is.
In case of waiting for information with an
RDS station without EON function
When there is no “EON” display with the op-
erations of steps 2 and 3 and the desired infor-
mation is selected in advance, waiting for the
desired information will be done only with the
presently received RDS station.
In regard to TP (Traffic Program) indicator
When the “TP” indicator is lit, this indicates that
the station or another station in the same net-
work is broadcasting traffic information. Even
without an EON reservation, traffic information
can be heard from the station when “TP” indi-
cator is lit for the presently received station.
R.D.S. (Radio Data System)
÷ When the unit is OFF or during recording, the EON
function does not operate.
÷ When the transmission of the selected program con-
tents ends in case of automatic reception with the EON
function, return will be made to the status directly before
operation of the EON function. When CD or TAPE play-
back has been interrupted, it will be continued from the
point of interruption.
Each press of the stop (7) key switches the PS
and PTY display alternately.
32
Application section
ENTER
CURSOR
INPUT
ENTER
SET
6
TV
VIDEO1
VIDEO2
CD
TUNER
TAPE
FUNCTION
Playback of CD
Listening in the desired sequence
(program playback)
Use the following procedure to program desired
tracks in a desired order. (up to 32 tracks)
Program desired tracks.
(In stop mode only)
1
1
Select the CD input.
2
Display the "CD" menu.
3
Select the message to be
displayed, "Program On"
or "Program Off".
4
Select the "Set".
5
Select a track number
and press the SET key.
6
To program other tracks,
repeat step
5
for each
track.
7
Press the ENTER key to
quit programming.
÷ When "Clear" is selected, the program being dis-
played will be cleared.
÷ Up to 32 tracks can be programmed. When "Pro-
gram Full" is displayed, no more track can be pro-
grammed.
÷ If you make a mistake in the middle, press the
HOME key to return to the basic screen.
INPUT
SET
CURSOR
SET
CURSOR
SET
CURSOR
SET
33
Application section
Play the programmed tracks.
6
BAND
¢4
–P.CALL–
1
Select the CD input.
2
Display the "CD" menu.
3
Select the message to be
displayed, "Program On".
4
Select the "Check".
5
Display a program number
and check the track pro-
grammed under it.
6
Press the ENTER key to
quit program checking.
2
÷ Pressing the 4 or ¢ key during playback skips
to one of the tracks programmed before or after
the current track.
÷ Pressing the 4 key once during playback returns
to the beginning of the current track.
Checking the program
(In stop mode only)
Use the following procedure to check the pro-
grammed tracks.
Clearing the program (In stop mode only)
Use the following procedure to clear all the pro-
grammed tracks from the program.
1
Select the CD input.
2
Display the "CD" menu.
3
Select the message to be
displayed, "Program On".
4
Select the "Off".
Playback of CD
ENTER
INPUT
SET
CURSOR
SET
CURSOR
SET
INPUT
SET
CURSOR
SET
CURSOR
SET
34
Application section
CURSOR
INPUT
SET
6
6
BAND
TV
VIDEO1
VIDEO2
CD
TUNER
TAPE
FUNCTION
Repeated playback
You can repeatedly listen to a favorite track or
disc.
Program repeat playback
÷ By programming only the desired tracks, it is
possible to perform the repeat playback of
only the programmed tracks later.
÷ To repeat playing a single track, program that
track only and start its repeat playback.
1
Select the CD input.
2
Display the "CD" menu.
3
Select the message to be
displayed, "Repeat Off" or
"Repeat On".
4
Select "On".
5
Start playback
÷ The entire disc will be played repeatedly.
÷ When both repeat playback and random playback
() are used simultaneously, all tracks in the disc
will be played in a random order and this random
playback will be repeated.
To cancel repeat playback
Select "Off" in step 4 to cancel repeat playback.
To stop operation in the middle
Press the HOME key to abort and cancel the
operation and return to the basic screen.
Playback of CD
INPUT
SET
CURSOR
SET
CURSOR
SET
35
Application section
CURSOR
INPUT
SET
6
TV
VIDEO1
VIDEO2
CD
TUNER
TAPE
FUNCTION
1
Select the CD input.
2
Display the "CD" menu.
3
Select the message to be
displayed, "Random Off"
or "Random On".
4
Select "On".
To stop operation in the middle
Press the HOME key to abort and cancel the
operation and return to the basic screen.
Listening to an unexpected title sequence
(random playback)
As the titles each time are selected randomly, the
music can be enjoyed without getting tired of it.
÷ It is not possible to perform random playback
of programmed tracks.
Random repeat playback
÷ When repeat playback is set before starting
random playback, the random playback of the
disc will be repeated.
Cancel the program mode. ¤
÷ The tracks in the entire disc will be played in a ran-
dom order, after which playback will stop.
To cancel random playback
Select "Off" in step 4 to cancel random play-
back.
Playback of CD
INPUT
SET
CURSOR
SET
CURSOR
SET
36
Application section
\
\
\
Convenient Recording Methods
Selection of the Recording Type
This unit provides the following recording fea-
tures in addition to normal recording. Select the
appropriate method according to the purpose of
recording.
Note that this cassette deck cannot record
onto Metal tapes.
NoteNote
Note
Recording all tracks in a CD onto tape
CD direct recording
CD direct recording
Records all tracks in a CD onto tape.
Recording a single track in CD onto tape
CD one-track recording
°
CD one-track recording
Records the CD track being played onto a
tape.
(This is convenient when you play a CD for
the first time but want to select and record
only the desired tracks.)
Recording desired CD tracks in a desired order onto tape
CD program recording
·
CD program recording
Records the programmed CD tracks in the
programmed order.
(This is convenient when you want to
program and record desired tracks in a CD
in a desired order.)
With recording onto tape, the track will be interrupted for the part of the guide tape at the tape reversal,
where recording is not possible. Please use single-side recording if this is to be avoided.
Note
Note
37
Application section
CURSOR
ENTER
SET
1
Display the "Function" menu.
2
Select the message to be
displayed, "CD
Tape
Rec".
3
Select the "Direct Rec".
4
Start recording
Recording an entire CD onto tape
(CD direct recording)
÷ This function is canceled when the program
mode is activated.
÷ This function is available only when the CD
player is in stop mode.
Convenient Recording Methods
Total number of tracks in CD,
total play time
CURSOR
SET
CURSOR
SET
CURSOR
SET
ENTER
Preparation
÷ Perform step
3
( "Select the tape transport direc-
tion") on page 26.
÷ Perform steps 2 to 4 of "Selecting the reverse
mode" on page 25.
To stop operation in the middle
Press the HOME key to abort and cancel the
operation and return to the basic screen.
38
Application section
CURSOR
ENTER
SET
1
Display the "Function" menu.
2
Select the message to be
displayed, "CD
Tape
Rec".
3
Select the "One Track
Rec".
4
Start recording
Recording every desired track in CD onto tape
(CD one-track recording)
During playback of a CD track, only the track being
played can be selected and recorded from the
beginning.
÷ CD random playback cannot be recorded.
Convenient Recording Methods
CD track No. being played, elapsed
play time of the track being played
CURSOR
SET
CURSOR
SET
CURSOR
SET
ENTER
To stop operation in the middle
Press the HOME key to abort and cancel the
operation and return to the basic screen.
Preparation
÷ Perform step
3
( "Select the tape transport direc-
tion") on page 26.
÷ Perform steps 2 to 4 of "Selecting the reverse
mode" on page 25.
39
Application section
CURSOR
ENTER
SET
1
Display the "Function" menu.
2
Select the message to be
displayed, "CD
Tape
Rec".
3
Select the "Program Rec".
4
Program CD tracks.
5
Start recording
Recording desired CD tracks in a desired order onto tape
(CD program recording)
The desired tracks in a CD can be programmed in
a desired order and recorded.
Convenient Recording Methods
Number of programmed CD tracks,
total play time of the program
÷ This function is available only when the CD
player is in stop mode.
Follow 5 to 7 in step 1 on
page 32.
CURSOR
SET
CURSOR
SET
CURSOR
SET
ENTER
To stop operation in the middle
Press the HOME key to abort and cancel the
operation and return to the basic screen.
Preparation
÷ Perform step
3
( "Select the tape transport direc-
tion") on page 26.
÷ Perform steps 2 to 4 of "Selecting the reverse
mode" on page 25.
40
Application section
¢4
–P.CALL–
CURSOR
ENTER
SET
4, ¢
Tone control and sound field effect adjustment
Use the following procedure to adjust the levels of
the Video1 and Video2 inputs.
Adjusting the external input level
1
Display the "Function" menu.
2
Select the message to be
displayed, "Input Level".
3
Select the "Video1" or
"Video2" .
4
Adjust the input level of
the selected input.
5
Press the ENTER key
The adjustment range is be-
tween +3 and -4.
CURSOR
Adjusting the subwoofer output level (NV-
600 only)
1
Display the "Function" menu.
2
Select the "S.W. Level".
3
Adjust the level of the
subwoofer output.
4
Press the ENTER key
The adjustment range is be-
tween 1 and 5.
CURSOR
SET
CURSOR
SET
ENTER
CURSOR
SET
CURSOR
SET
¢4
–P.CALL–
ENTER
41
Application section
¢4
–P.CALL–
CURSOR
ENTER
SET
4, ¢
CURSOR
Bass Boost and tone control
The Bass Boost function allows you to enhance
or compensate for the low frequencies and the
tone control function is used for fine adjust-
ments of the bass (low frequencies) and treble
(high frequencies).
Selecting the bass boost
(NV-500 only )
1
Display the "Function" menu.
2
Select the "Listen Mode".
3
Select the message to be
displayed, "Bass Boost
Off" or "Bass Boost On".
4
Select the message to be
displayed, "On" or "Off",
and press the SET key.
Tone adjustment
The lowest and highest frequency bands can be
adjusted independently.
1
Display the "Function" menu.
2
Select the "Tone Control".
3
Select the message to be
displayed, "Bass" or
"Treble".
4
Adjust the level of the
selected tone.
5
Press the ENTER key
The adjustment range is be-
tween +4 and -4.
Tone control and sound field effect adjustment
÷ The sound field effects of Bass Boost and tone
control cannot be used simultaneously.
The tone control setting is
switched off.
The tone control setting is
recalled whenever the Bass
Boost setting is switched off.
The bass boost setting is
switched off.
CURSOR
SET
CURSOR
SET
CURSOR
SET
CURSOR
SET
CURSOR
SET
CURSOR
SET
ENTER
42
Application section
CURSOR
ENTER
SET
4, ¢
Dolby Virtual setting
Tone control and sound field effect adjustment
The Dolby Virtual function is designed to provide
a simulated surround effect from two speakers
on the left and right. This is a convenient function
for playing a movie, etc.
÷ The DSP mode is canceled when Dolby Vir-
tual is set.
1
Display the "Function" menu.
2
Select the "Listen Mode".
3
Select the message to be
displayed, "Virtual On" or
"Virtual Off".
4
Select "On" or "Off".
Setting ON or OFF
Select level
1
Display the "Function" menu.
2
Select the "Listen Mode".
3
Select the message to be
displayed, "Virtual On".
4
Select the "Effect Level ".
5
Select the “Level 1”,
“Level 2” or “Level 3”
6
Press the ENTER key
CURSOR
SET
CURSOR
SET
CURSOR
SET
CURSOR
SET
CURSOR
SET
CURSOR
SET
CURSOR
SET
CURSOR
SET
ENTER
¢4
–P.CALL–
43
Application section
CURSOR
ENTER
SET
4, ¢
Tone control and sound field effect adjustment
The DSP (Digital Surround Processor) controls the
tone of a signal in the digital form and makes
sound processing without quality degradation
possible. The DSP built into this unit provides
appropriate tone patterns (equalizing patterns)
for major musical categories.
DSP mode setting
1
Display the "Function" menu.
2
Select the "Listen Mode".
3
Select the message to be
displayed, "DSP On” or
“DSP Off”.
4
Select the desired DSP
pattern.
÷ The Dolby Virtual function is canceled when
the DSP mode is set.
“Off”
“Stadium”
“Arena”
“Live house”
CURSOR
SET
CURSOR
SET
CURSOR
SET
CURSOR
SET
This display shows the example with the NV-
500.
44
Application section
CURSOR
ENTER
SET
4, ¢
¢4
–P.CALL–
SET
Timer operation
Adjust the clock before setting the timer.
O.T.T. :
Starts playback of the selected input source when the set time comes and turns power off in an hour. This
program is executed only once every time after it is set.
Timer playback, timer recording:
Plays the selected input source (or records tuner broadcasting or external input source) in the set time zone.
SLEEP timer:
Turns power off automatically after the set period of time.
When more than one timer setting overlaps
With this unit, the O.T.T. on time, the timer play-
back on time/off time and the timer recording on
time/off time can be set independently. If more
than one timer setting overlaps in a certain pe-
riod, the timer functions are activated in the fol-
lowing priority order:
1 O.T.T.
2 Timer playback
3 Timer recording
Setting the O.T.T.
1
Display the "Function" menu.
2
Select the message to be
displayed, "O.T.T. Off" or
“O.T.T. On”.
3
Select the message to be
displayed, "On”.
4
Set the timer start time.
5
After setting the start
time, press the ENTER
key.
6
After completing the set-
ting, set the power OFF.
To return time
To advance time
÷ Select "Off" when you want to cancel the O.T.T. timer.
÷ The time is variable in 5-minute steps.
÷ When the timer has been set and power set to OFF,
the STANDBY/TIMER indicator lights up in amber.
CURSOR
SET
CURSOR
SET
CURSOR
SET
ENTER
÷ In other areas than the UK, Europe and Australia,
the clock shows the time of the day in the 12-hour
system.
When the time set by the timer comes, the last source
which was selected before the power was switched off
will be played back.
45
Application section
CURSOR
ENTER
SET
4, ¢
Setting the timer playback
Timer playback includes normal timer playback
and AI (Artificial Intelligence) timer playback.
Normal timer playback:
Starts playback of the selected source at the set
on time and turns power OFF at the set off time.
AI timer playback:
Increases the playback volume gradually after
the start of timer playback.
1
Display the "Function" menu.
2
Select the message to be
displayed, "Timer Play
Off" or “Timer Play On”.
3
Select the message to be
displayed, "On”.
4
Set the on time.
5
Set the off time.
6
Select the input to be
played by timer.
÷ Select "Off" when you want to cancel the timer.
÷ It is not permitted to set the same time of day as
the on time and off time.
To return to the previous operation step in the middle,
select "Back" with the CURSOR key and press the SET
key. Select "Next" to advance to the next step.
¢4
–P.CALL–
SET
CURSOR
SET
CURSOR
SET
CURSOR
SET
¢4
–P.CALL–
SET
¢4
–P.CALL–
SET
Timer operation
Continued to next page
46
Application section
¢4
–P.CALL–
SET
¢4
–P.CALL–
SET
¢4
–P.CALL–
SET
7
Select a preset radio station.
(This step is required only
when the tuner input is
selected in the above.)
8
Select the message to be
displayed, "AI-Play" or
“Normal-Play”.
9
Press the ENTER key to
complete the setting.
0
After completing the set-
ting, set the power OFF.
Sleep Timer (Sleep)
1
Display the "Function" menu.
2
Select the message to be
displayed, "Sleep On” or
"Sleep OFF”.
3
Set the time period until
the power is to be turned
OFF.
÷ The time period can be set in 10-minute steps from
"Off" up to "90" minutes.
÷ Selecting "Off" cancels the sleep timer setting.
÷ The back light of the remote control unit turns off
while the sleep timer is active.
÷ The power will turn off when the set time period
has elapsed.
÷ When the timer has been set and power set to OFF,
the STANDBY/TIMER indicator lights up in amber.
ENTER
CURSOR
SET
CURSOR
SET
Timer operation
47
Application section
CURSOR
ENTER
SET
4, ¢
Timer recording
1
Display the "Function" menu.
2
Select the message to be
displayed, "Timer Rec Off"
or “Timer Rec On”.
3
Select the message to be
displayed, "On”.
4
Perform the setting op-
eration in steps
4
to
5
under "Setting the timer
playback".
5
Select the input source to
be recorded.
6
Select a preset radio station.
7
Press the ENTER key.
8
After completing the set-
ting, set the power OFF.
÷ Select "Off" when you want to cancel the timer.
÷ "Tuner", "Video1" or "Video2" can be selected.
To return to the previous operation step in the middle,
select "Back" with the CURSOR key and press the SET
key. Select "Next" to advance to the next step.
Timer recording is used to record a source onto a
tape.
The TUNER or the component connected to the
Video1 or Video 2 input can be selected as the
source.
(This step is required only when the tuner
input is selected in the above.)
¢4
–P.CALL–
SET
¢4
–P.CALL–
SET
CURSOR
SET
CURSOR
SET
CURSOR
SET
Timer operation
÷ Audio is not output during timer recording.
48
Application section
CURSOR
SET
CURSOR
SET
TV
VIDEO1
VIDEO2
CD
TUNER
TAPE
FUNCTION
Checking the time information display of CD
The remote control unit can display the time
information of CD such as the playing time and
total time.
The time information can be checked while the
CD is playing or stopped.
1
Display the "Function" menu.
2
Select the information
item to be displayed.
The items as shown below can
be selected.
CD Single Time display
During stop in normal mode:
Playing time of the first track.
During playback in normal mode:
Playing time of the track being played.
During stop in program mode:
Playing time of the first programmed
track.
During playback in program mode:
Playing time of the track being played.
In normal mode:
Total playing time of the disc.
In program mode:
Total playing time of the programmed
tracks.
CD Total Time display
CURSOR
SET
49
Application section
CURSOR
ENTER
SET
4, ¢
¢4
–P.CALL–
SET
ENTER
Adjusting the display contrast
Use the following procedure to adjust the density of the
display on the remote control unit.
1
Display the "Function" menu.
2
Select the message to be
displayed, "Contrast".
3
Adjust the contrast.
4
Press the ENTER key
CURSOR
SET
CURSOR
SET
50
Application section
CURSOR
ENTER
SET
CURSOR
SET
SET
ENTER
1
Display the "Function" menu.
2
Select the message to be
displayed, "TV".
3
Select the manufacturer.
4
Select the type of the
remote control codes.
5
Check the remote control
operations.
6
If the operations are nor-
mal, press the ENTER key
to set it.
Registering the TV to be used
Remote control of external components
Registering the controlled components in the remote control unit
The remote control unit can also be used to control the
major functions of externally connected components
such as a TV, VCR and DVD player.
To make the control possible, it is required to select the
manufacturer and type (VCR, DVD, etc.) of each com-
ponent and register it in the memory of the remote
control unit.
Note that, with components from certain manufactur-
ers or of certain types, remote control may not be
available or the controllable functions may be limited.
÷ Press the SET key and ensure that the component
is turned ON.
÷ If normal operation cannot be performed, place the
cursor on "Back" and re-select the code type. Be
sure to check the results later.
The manufacturer list is displayed.
CURSOR
SET
CURSOR
SET
CURSOR
SET
51
Application section
Registering the component connected to the
rear-panel Video1 or Video2 input
1
Display the "Function" menu.
2
Select the message to be
displayed, "Video1" or
"Video2".
3
Select the type of the com-
ponent (VCR, DVD, etc).
4
Select the manufacturer.
5
Select the type of the
remote control codes.
6
Check the remote control
operations.
7
If the operations are nor-
mal, press the ENTER key
to set it.
÷ Press the SET key and ensure that the component
is turned ON.
÷ If normal operation cannot be performed, place the
cursor on "Back" and re-select the code type. Be
sure to check the results later.
÷ The cable tuner and DSS operations are not avail-
able in other areas than the U.S.A. and Canada.
÷ The displayed information is variable depending on
areas.
The manufacturer list is displayed.
CURSOR
SET
SET
ENTER
CURSOR
SET
CURSOR
SET
CURSOR
SET
CURSOR
SET
Remote control of external components
52
Application section
TV
VIDEO1
VIDEO2
CD
TUNER
TAPE
FUNCTION
TV
VIDEO1
VIDEO2
CD
TUNER
TAPE
FUNCTION
TV
VIDEO1
VIDEO2
CD
TUNER
TAPE
FUNCTION
VOLUME
CLOCK MUTE
CONFIRM/DEMO
HOME
INPUT
DIRECTION
SET ENTER
REC
– P.CALL –
BACK LIGHT
CURSOR
6
7
¢4
Remote control of external components
By registering the externally connected components such as a TV, VCR and DVD player in the remote
control unit, it can be used to control the major functions of the external components.
Select the input corresponding to the com-
ponent to be remote controlled.
The display show the function names and/or sym-
bols of the 7 available remote control keys. The
correspondence between the displayed keys and
panel keys is as shown below.
If the remote control keys are provided in more
than one display page, each page can be switched
every time the SET key is pressed.
Remote control of external components
CURSOR
SET
53
Application section
TV control screen
This screen consists of a single page.
VCR control screen
This consists of 2 pages.
Each press of the SET key switches the pages alter-
nately.
DVD control screen
This consists of 3 pages.
Each press of the SET key switches the pages alternately.
Cable Tuner control screen (for U.S.A.
& Canada)
This screen consists of a single page.
DSS control screen (for U.S.A. & Canada)
This consists of 2 pages.
Each press of the SET key switches the pages alter-
nately.
Symbol on the
Display Function
remote control
6 BAND Vol 5 Volume Up
7 Vol Volume Down
¢ Ch 5 Channel Up
4 Ch Channel Down
ENTER PWR Power
DIRECTION MUTE Muting
REC INPUT Input selection
Symbol on the
Display Function Display Function
remote control
6 BAND Play Play
77Stop 7 Stop
¢¡Fast forward Ch5 Channel Up
41Fast reverse Ch Channel Down
ENTER PWR Power PWR Power
DIRECTION PAUSE Pause AUDIO* Audio switching
REC REC Record INPUT Input selection
Symbol on the
Display Function
remote control
6 BAND Vol 5 Volume up
7 Vol Volume down
¢ Ch 5 Channel up
4 Ch Channel down
ENTER PWR Power
DIRECTION
REC
Symbol on the
Display Function Display Function
remote control
6 BAND Cursor
7 Cursor
¢ Ch5 Channel up Cursor
4 Ch Channel down Cursor
ENTER PWR Power ENTER Enter
DIRECTION INFO Informatiom MENU Menu
REC INPUT Input selection GUIDE Guide
Symbol on the
Display Function Display Function Display Function
remote control
6 BAND Play Cursor Cursor
77Stop Cursor Cursor
¢¢Forward skip Cursor Cursor
44Reverse skip Cursor Cursor
ENTER PWR Power ENTER Enter ENTER Enter
DIRECTION PAUSE Pause OSD OSD MENU Menu
REC RTN Return RTN Return
*Note: This function is available only with other models than the Europe, UK
and the U.S.A. destination models.
Remote control of external components
54
Knowledge section
Cleaning the head section
Cleaning the heads and peripheral components
For maintaining the best condition of the deck and for longer service life, always
keep the heads (recording / playback / erase), capstan and pinch roller clean.
To clean them, perform the following:
1.Open the cassette holder.
2.Using a cotton swab dipped in alcohol, clean the head (recording / playback /
erase), capstan and pinch roller carefully.
Demagnetizing the head
When the recording / playback head is magnetized, the sound quality will
deteriorate. In such a case, demagnetize the head using a commercially available
demagnetizer (head eraser).
Maintenance
There are precisely aligned parts around the heads, including the tape guides.
When cleaning, pay special attention so as not to apply shock to them.
NoteNote
Note
Cotton swab
Head
Capstan
Pinch roller
Tape guides
Caution on condensation
Condensation (of dew) may occur inside the unit when
there is a great difference in temperature between this
unit and the outside.
This unit may not function properly if condensation oc-
curs. In this case, leave the unit for a few hours with the
power left ON, and restart the operation after the con-
densation has dried up.
Be specially cautious against condensation in a fol-
lowing circumstance:
When this unit is carried from a place to another across a
large difference in temperature, when the humidity in the
room where this unit is installed increases, etc.
Reference
Maintenance of the Set
When the front panel, the case, etc. becomes dirty, wipe
with a soft, dry cloth. Do not use thinner, alcohol, etc., as
these can cause discoloration.
In regard to contact cleaners
Do not use contact cleaners because it could cause a mal-
function. Be specially careful not to use contact cleaners
containing oil, for they may deform the plastic component.
Stored contents which are
cleared immediately when
power plug is unplugged
from power outlet
Stored contents which are
cleared in at least a day after
power plug is unplugged
from power outlet
Clock display
Amplifier section
"on/standby" status
(ON or STANDBY)
Last input selection
Volume control value
Tone control levels
Video1/Video2 input level
Balance setting
Tuner section
Receiving band
Frequency
Preset stations
Auto/mono setting
Program timer setting
contents
Cassette deck unit
Transport direction
Dolby NR
Reverse mode
Memory backup function
Note related to transportation and movement
Before transporting or moving this unit, carry out the
following operations.
1 Select the CD input
2 Press the 0 key and take out the CD.
3 Ensure that "No Disc" is displayed.
4 Wait for a few seconds, then set the power
OFF.
Important Items
CD
6
TUNER
/BAND
0
55
Knowledge section
Safety tab (accidental erasure prevention tab)
After an important recording has been finished, break the
safety tab, to prevent the recorded contents from being
erased or recorded on accidentally.
For B side
For A side
To store cassette tapes
Do not store the tapes in a place which is subject to
direct sunlight, or near equipment that generates heat.
Keep the cassette tapes away from any magnetic field.
To re-record
Apply tape only to the position where
the tab has been removed.
When there is slack in the tape
In such a case, insert a pencil into the reel hole and wind
the reel hub to remove the slack.
N
S
1.Longer tape than 110 minutes cassette tape
Since longer tape than 110 minutes cassette tape is very thin, the tape could adhere to the pinch roller or be
easily broken. It is recommended that these tapes not be used with this unit to prevent possible damage.
2.Endless tapes
Do not use an endless tape, as this could damage the mechanism of the unit.
Notes
Notes
Notes on cassette tape
Label side
Playing side
Cleaning
If fingerprints or foreign matter be-
come attached to the disc, lightly wipe
the disc with a soft cotton cloth (or
similar) from the center of the disc
outwards in a radial manner.
Storage
When a disc is not to be played for
a long period of time, remove it from
the player and store it in its case.
Handling
Hold the discs so that you do not
touch the playing surface.
Discs which can be played with this unit
CD (12 cm, 8 cm), and the audio part of CDV, CD-G, CD-EG
and CD-EXTRA.
Use discs that comply with the IEC standard, for example
a disc carrying
DIGITAL AUDIO
COMPACT
the marking on the label surface.
Disc handling precautions
Disc accessories
The disc accessories (stabilizer, protection sheet, protec-
tion ring, etc.) which are marketed for improving the sound
quality or protecting discs as well as the disc cleaner should
not be used with this system because they may cause
malfunction.
Do not attach paper or tape to ei-
ther the playing side or the label side
of the discs.
Sticker
Sticky paste
Never play a cracked or warped disc
During playback, the disc rotates at high speed in the player.
Therefore, to avoid danger, never use a cracked or deformed
disc or a disc repaired with tape or adhesive agent.
Please do not use discs which are not round because they
may cause a malfunction.
Important Items
56
Knowledge section
Note to CATV system installer
This reminder is provided to call the CATV system installer's
attention to Article 820-40 of the NEC that provides guidelines
for proper grounding and, in partiqular, specifies that the cable
ground shall be connected to the grounding system of the build-
ing, as close to the point of cable entry as practical
Use of controls or adjustments or performance of pro-
cedures other than those specified herein may result
in hazardous radiation exposure.
In compliance with Federal Regulations, following are
reproductions of labels on, or inside the product re-
lating to laser product safety.
KENWOOD CORPORATION
2967-3, ISHIKAWA-CHO,
HACHIOJI-SHI,
TOKYO, JAPAN
KENWOOD CORP. CERTIFIES THIS EQUIPMENT
CONFORMS TO DHHS REGULATIONS NO. 21 CFR
1040.10, CHAPTER 1, SUBCHAPTER J.
CAUTION:
Location: Back Panel
This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful
interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this
equipment if an unauthorized change or modification is made.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment may
cause harmful interference to radio communications, if it is not installed and used in accordance with the instructions. However, there
is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
– – Reorient or relocate the receiving antenna.
– – Increase the separation between the equipment and receiver.
– – Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– – Consult the dealer or an experienced radio / TV technician for help.
FCC WARNING
Dolby noise reduction manufactured under license from Dolby
Laboratories. “DOLBY” and the double-D symbol are trade-
marks of Dolby Laboratories.
WARNING NOTICE:
IN MOST CASES IT IS AN INFRINGEMENT OF COPY-
RIGHT TO MAKE COPIES OF TAPES OR DISCS WITH-
OUT THE PERMISSION OF THE COPYRIGHT OWNERS.
ANYONE WISHING TO COPY COMMERCIALLY AVAIL-
ABLE TAPES OR DISC SHOULD CONTACT THE ME-
CHANICAL COPYRIGHT PROTECTION SOCIETY LIMITED
OR THE PERFORMING RIGHTS SOCIETY LIMITED.
As an ENERGY STAR
®
Partner, Kenwood Cor-
poration has determined that this products meets
the
ENERGY STAR
®
guidelines for energy
efficiency.
This product can save energy. Saving energy reduces air
pollution and lowers utility bills.
57
Knowledge section
In case of difficulty
Operation to reset
The microcomputer may fall into malfunction (impos-
sibility to operate, erroneous display, etc.) when the
power cord is unplugged while unit is ON or due to
an external factor. In this case, execute the following
procedure to reset the microcomputer and return it
to normal condition.
Unplug the power cord from the power outlet then,
while holding the CD Open close (0) key depressed,
plug the power cord again.
After some time, the power will be switched off
and return will be made to the initial status.
÷ Please note that resetting the microcomputer clears
the contents stored in and it returns to condition when
it left the factory.
What seems to be a malfunction is not always so. Before calling for service, check the following table
according to the symptom of your trouble.
RemedyCauseSymptom
Amplifier section/Speakers
÷ Connect properly referring to
System
c
onnection”.
÷ Adjust to an required volume.
÷ Switch MUTE OFF.
÷ Unplug the headphone plug.
÷ Turn the unit OFF, remove the short-
circuit and turn the unit ON again.
÷ Insert correctly.
÷ Connect properly referring to “System
connection”.
÷ Adjust the optimum left and right bal-
ance.
Sound is not produced.
No sound from the head-
phones.
Sound is not produced from
the left or right speakers.
÷ The speaker cords are disconnected.
÷ The volume control is set to the mini-
mum position.
÷ The MUTE key is switched ON.
÷ The headphone plug is inserted into the
jack.
÷ The speaker cords are short-circuited.
÷ Imperfect insertion.
÷ The speaker cords are disconnected.
÷ The BALANCE is set completely to the
left or right channel.
RemedyCauseSymptom
÷ Adjust the present time again.
÷ Adjust the present time again.
÷ Adjust the present time referring to
“Clock adjustment”.
÷ Set the timer ON time and OFF time.
÷ Press the ON STANDBY key to set up
the execution.
÷ Connect antennas.
÷ Select a band.
÷ Tune to the frequency of the desired
station.
÷ Install the outdoor antenna in an apart
position from the road.
÷ Switch the suspected electric appliance
OFF.
÷ Install the TV or the system at an in-
creased distance between them.
÷ Preset stations with tunable frequen-
cies.
÷ Preset stations again.
The clock display blinks
without changing the fig-
ures.
Timer operation is not pos-
sible.
Radio stations cannot be
received.
Noise interferes.
A station has been preset but
it cannot be received by
pressing the P.CALL key.
÷ There was a power failure.
÷ The power cord was unplugged from the
outlet.
÷ The present time has not been adjusted
or there was a power failure.
÷ The timer ON time and OFF time have
not been set.
÷ The timer execution was not set up.
÷
The antennas have not been connected.
÷ A proper broadcasting band has not been
selected.
÷ The frequency of the station to be re-
ceived is not tuned.
÷ Car ignition noise.
÷ Influence of an electric appliance.
÷ A TV set is installed near the system.
÷ The frequency of the preset station is
not tunable.
÷ The preset memory has been cleared
because the power cord has been un-
plugged for a long period.
$
$
t
7
*
)
8
&
&
8
&
Tuner section
58
Knowledge section
In case of difficulty
RemedyCauseSymptom
CD player section
÷ Place the disc properly, with the label
side facing upward.
÷ Place the disc properly.
÷ Clean the disc referring to “Disc han-
dling precautions”.
÷ Try another disc.
÷ Refer to “Caution on condensation” and
remove the condensation by evaporation.
÷ Place a disc in the CD player.
÷ Press the 6 key.
÷ Clean the disc referring to “Disc han-
dling precautions”.
÷ Try another disc.
÷ Clean the disc referring to “Disc han-
dling precautions”.
÷ Try another disc.
÷ Install the unit in a place not subject to
vibrations.
÷ This is not a malfunction.
A CD is placed in the player
but it cannot be played.
Sound is not produced.
Sound skips.
“Text Full” is displayed
÷ The disc is placed upside down.
÷ The disc position is displaced.
÷ The disc is extremely dirty.
÷ The disc is scratched.
÷ Dew is condensed on the optics lens.
÷ The disc has not been placed.
÷ The player is not put to the play mode.
÷ The disc is extremely dirty.
÷ The disc is scratched.
÷ The disc is dirty.
÷ The disc is scratched.
÷ The player is subject to vibration.
÷ Too much text data has been stored.
T
R
T
T
Remote control unit
Symptom Cause Remedy
Remote control operation is
not possible.
The “Low Battery” alarm is
displayed.
÷ Batteries are exhausted.
÷ The remote control is too far away from
the system, the controlling angle is devi-
ated or there is an obstacle in between.
÷ The component to be played is not loaded
with a CD or cassette tape.
÷ Batteries are exhausted.
÷ Replace with new batteries.
÷ Operate the unit inside the remote con-
trollable range.
÷ Load a CD or cassette tape in the com-
ponent to be played.
÷ Replace with new batteries.
@
@
@
59
Knowledge section
RemedyCauseSymptom
÷ Clean the head referring to “Mainte-
nance”.
÷ Try another tape.
÷ Play a recorded tape.
÷ Close the holder completely.
÷ Press operation keys in more than a few
seconds after closing the cassette holder.
÷ Press operation keys after waiting for
more than 4 seconds.
÷ Insert a tape.
÷ Try another tape.
÷ Change the tape transport direction or
reverse the tape insertion orientation.
÷ Press in stop mode.
÷ Reset the microcomputer.
÷ Clean the head referring to “Mainte-
nance”.
÷ Try another tape.
÷ Adjust the Video 1, Video 2 input level.
÷ Try another tape.
÷ Demagnetize the head referring to “Main-
tenance”.
÷ Install the system at a distance from
other electric appliances and TV.
÷ Set the "Dolby NR" to on.
÷ Clean the head referring to “Mainte-
nance”.
÷ Wind the tape again by fast forwarding,
rewinding or playing from an end to the
other.
÷ Use a cassette with an unbroken record-
ing protect tab or block the hole.
÷ Close the holder completely.
÷ Set the input selector to the source to be
recorded.
÷ Change the tape transport direction or
reverse the tape insertion orientation.
Sound cannot be produced
by pressing the play key.
No operation occurs even
when an operation key is
pressed.
The cassette holders cannot
be opened by pressing the
“PUSH OPEN” area.
Sound is harsh or high
frequencies are not repro-
duced.
Sound is distorted.
Noise is noticeable.
Sound vibrates.
Recording cannot be started
by pressing the record key.
R
¢
¢
¢
U
R
R
R
T
¢
§
§
÷ The head is dirty.
÷ The tape is wound too tight due to
irregular winding.
÷ A nonrecorded tape is played.
÷ The cassette holder is not closed com-
pletely.
÷ The operation key is pressed immedi-
ately after closing the cassette holder.
÷ The operation key is pressed in less than
4 seconds after turning the power ON.
÷ A tape is not inserted in the unit.
÷ The tape is wound too tight due to
irregular winding.
÷ The tape is fully wound to one of the
reels.
÷ The key is pressed during recording or
playback.
÷ The microcomputer is malfunctioning
due to external noise.
÷ The head is dirty.
÷ The tape is stretched or shrunk.
÷ The recording level has not been ad-
justed. (During Video 1, Video 2 input
operation)
÷ The tape being played was recorded
with distorted sound.
÷ The tape head is magnetized.
÷ External noise is induced.
÷ A tape recorded with Dolby NR ON is
played with "Dolby NR" off.
÷ The capstans or pinch rollers are dirty.
÷ The tape is wound irregularly.
÷ The recording protect tab of the cas-
sette has been broken.
÷ The cassette holder is not closed com-
pletely.
÷ The TAPE input is selected.
÷ The tape is fully wound to one of the reels.
Cassette deck
60
Knowledge section
INDEX
[A]
A.R.M. ...................................................................... 27
ACTIVE indicator ...................................................... 11
Adjusting the display contrast ................................. 49
Adjusting the external input level ............................ 40
Adjusting the left and right volume balance ............ 17
Adjusting the subwoofer output level ..................... 40
AI timer playback ..................................................... 45
Auto preset ............................................................. 20
[B]
Basic use method .................................................... 16
[C]
Cable Tuner control screen...................................... 53
CD direct recording .................................................. 37
CD one-track recording ............................................ 38
CD program recording ............................................. 39
CHANNEL SPACE setting ....................................... 10
Checking the time information display of CD .......... 48
Cleaning the head section ....................................... 54
Clock adjustment ..................................................... 14
Communication indicator ......................................... 11
CONFIRM/DEMO key........................................... 6,13
[D]
Demonstration ........................................................... 6
Disc handling precautions........................................ 55
Dolby Virtual setting ................................................ 42
DSP mode setting.................................................... 43
DSS control screen .................................................. 53
DVD control screen.................................................. 53
[E]
EON ......................................................................... 30
[F]
Fast forwarding/rewinding or skipping tape ............ 25
[H]
HOME key ............................................................... 13
[I]
In regard to CD-TEXT ............................................... 23
[M]
Maintenance ............................................................ 54
Manual preset ......................................................... 21
[N]
Normal timer playback ............................................. 45
Notes on cassette tape ........................................... 55
[O]
O.T.T. ....................................................................... 44
One-touch operation ................................................ 17
[P]
Playback of CD......................................................... 22
Playback of tape....................................................... 24
Program playback .................................................... 32
PTY search ............................................................... 29
[R]
R.D.S. ....................................................................... 28
Random playback..................................................... 35
RDS auto memory ................................................... 20
Receiving broadcast station..................................... 18
Recording on TAPE .................................................. 26
Reference ................................................................ 54
Remote control of external components................. 50
Repeated playback................................................... 34
[S]
Selecting Dolby NR .................................................. 25
Selecting the bass boost ......................................... 41
Selecting the reverse mode .................................... 25
Setting the timer playback ....................................... 45
Skipping tracks......................................................... 23
Sleep Timer (Sleep).................................................. 46
Specifications........................................................... 62
Standby mode.......................................................... 17
STANDBY/TIMER indicator...................................... 17
Switching between stereo tuning and monaural tuning
................................................................................. 19
[T]
Timer operation........................................................ 44
Timer recording........................................................ 47
To eject the disc ...................................................... 23
To pause playback (CD) ........................................... 23
To receive a station that has not been preset ......... 19
To stop playback (CD) .............................................. 23
To stop playback (Tape) ........................................... 24
Tone adjustment ...................................................... 41
TV control screen ..................................................... 53
[V]
VCR control screen .................................................. 53
Volume adjustment.................................................. 16
61
Knowledge section
Menu display chart
"TUNER" menu display
<Reception Mode>
Stereo/Mono
Stereo
Mono
Direct Tuning
<Memory>
Auto Memory
(#2)
Auto Preset
(#1)(#3)
Manual Memory
<RDS Mode>
(#2)
EON ***
(#2)
PTY ***
(#2)
"CD" menu display
<Play Mode>
Repeat On (Off)
On
Off
Random On (Off)
On
Off
Program On (Off)
Set
Check
Off
"Tape" menu display
Dolby NR
On
Off
Direction
One Way
Reverse
Endless
"TV" remote display
"Video 1" remote display
"Video 2" remote display
"Function" menu display
<Sound Mode>
Listen Mode
Virtual
Virtual On (Off)
On
Off
Effect
DSP Mode
DSP On (Off)
Off
Stadium
Arena
Live house
Bass Boost On (Off)
(NV-500 only)
On
Off
Balance
Tone Control
Bass
Treble
Input Level
Video1
Video2
S.W. Level (NV-600 only)
<Time INFO>
CD Single
CD Single Time
CD Total
CD Total Time
<Timer Mode>
Sleep
O.T.T.
On
Off
Timer Play
On
Source Select
Off
<Rec Options>
CDTape Rec
One Track Rec
Direct Rec
Program Rec
Timer Rec On (Off)
On
Source Select
Off
<Setup IR>
TV
(manufacturer list)
(type of codes )
Video 1
VCR
(manufacturer list)
(type of codes )
Cable
(#1)
(manufacturer list)
(type of codes )
DSS
(#1)
(manufacturer list)
(type of codes )
DVD
(manufacturer list)
(type of codes )
Video 2
VCR
(manufacturer list)
(type of codes )
Cable
(#1)
(manufacturer list)
(type of codes )
DSS
(#1)
(manufacturer list)
(type of codes )
DVD
(manufacturer list)
(type of codes )
<Display>
Contrast
(#1) : This mark refers to item for the U.S.A. and Canada.
(#2) : This mark refers to item for Europe and U.K.
(#3) : This mark refers to item for other countries.
62
Knowledge section
Specifications
[Amplifier section]
Output power
(U.S.A. and Canada)
Rated output power (front channel only)
30 watts per channel minimum RMS, both chan-
nels driven, at 8 from 100 Hz to 20 kHz with no
more than 0.9% total harmonic distortion.(FTC)
Effective output power
FRONT
(1 kHz, 10 % T.H.D., at 8 ) ............ 40 W + 40 W
SUBWOOFER
(65 Hz, 10 % T.H.D., at 4 ) ........................ 80 W
(Europe and U.K.)
Rated output power (front channel only) (DIN)
(1 kHz, 0.7 % T.H.D., at 8 ) ............ 35 W + 35 W
Effective output power
FRONT
(1 kHz, 10 % T.H.D., at 8 ) ............ 40 W + 40 W
SUBWOOFER
(65 Hz, 10 % T.H.D., at 4 ) ........................ 80 W
(Other countories)
Rated output power during (front channei only)
(1 kHz, 1 % T.H.D., at 8 ) ............... 35 W + 35 W
Effective output power during STEREO operation
FRONT
(1 kHz, 10 % T.H.D., at 8 ) ............ 40 W + 40 W
SUBWOOFER
(65 Hz, 10 % T.H.D., at 4 ) ........................ 80 W
Frequency responce
FRONT
(VIDEO1/VIDEO2) ... 100 Hz ~ 40 kHz (+0 dB ~ -3 dB)
SUBWOOFER
(VIDEO1/VIDEO2) ....... 5 Hz ~ 100 Hz (+0 dB ~ -3 dB)
Signal to noise ratio
VIDEO1/VIDEO2 .............................................. 90 dB
Input sensitivity/impedance
VIDEO1/VIDEO2
(U.S.A, Canada, Europe and U.K.) ....
230 mV/47 k
(Other countories) ......................... 200 mV/47 k
Output level/impedance
REC OUT (VIDEO1)
(U.S.A, Canada, Europe and U.K.) ....
230 mV/470
(Other countories) ......................... 200 mV/470
[Video section]
Input / Output VIDEO
(Composite) ........................................... 1 Vp-p/75
[Tuner section]
FM tuner section
Tuning frequency range ........... 87.5 MHz ~ 108 MHz
Main unit (RXD-NV600)
[Satellite speaker system]
Enclosure ..... Bass-reflex type, magnetically shielded
Speaker configuration
Woofer ............................ 80 mm (3-1/8”), cone type
Tweeter............................. 19 mm (3/4”), dome type
Impedance ................................................................ 8
Maximum input level .............................................. 40 W
Dimensions .................................. W: 158 mm (6-1/4”)
H : 257 mm (10-1/8”)
D : 152 mm (6”)
Weight (net) ....
2.0 kg (1 piece/including the speaker stand)
[Subwoofer system]
Enclosure ..... Bass-reflex type, magnetically shielded
Speaker configuration
Woofer .......................... 160 mm (6-1/2”), cone type
Impedance ................................................................ 4
Maximum input level .............................................. 80 W
Dimensions .................................. W: 206 mm (8-1/8”)
H : 280 mm (11”)
D : 387 mm (15-1/4”)
Weight (net) ............................................ 6.5 kg(1 piece)
KENWOOD follows a policy of continuous advancements in development. For this reason specifications may be
changed without notice.
÷ Sufficient performance may not be exhibited at extremely cold locations (where water freezes).
Notes
Notes
MW (AM) tuner section
Tuning frequency range
(For U.S.A and Canada) ...... 530 kHz ~ 1,700 kHz
(For Europe and U.K,) ......... 531 kHz ~ 1,602 kHz
(For other countories)
9 kHz step ........................ 531 kHz ~ 1,602 kHz
10 kHz step ........................ 530 kHz ~ 1,610 kHz
LW tuner section (For U.K. only)
Tuning frequency range .............. 153 kHz ~ 279 kHz
[CD player section]
Laser ..............................................Semiconductor laser
Wow and flutter............................. Unmeasurable limit
[Cassette deck section]
Track ........................................4 track, 2 channel stereo
Recording system ................................. AC bias system
(Frequency: 105 kHz)
Heads
Playback / recording head ....................................... 1
Erasing head ............................................................. 1
Motor.............................................................................. 1
Fast winding time ........................ Approx. 110 seconds
(C-60 tape)
[General]
Power consumption ............................................. 100 W
Dimensions (Attached the remote control unit)
............................................. W : 285 mm (11-1/4”)
H : 252 mm (9-15/16”)
D : 368 mm (14-1/2”)
Weight (Include the remote control unit) ......... 8.4 kg
Speakers (LS-NV600S)
NV-600
63
Knowledge section
Specifications
KENWOOD follows a policy of continuous advancements in development. For this reason specifications may be
changed without notice.
÷ Sufficient performance may not be exhibited at extremely cold locations (where water freezes).
Notes
Notes
[Amplifier section]
Output power
(U.S.A. and Canada)
Rated output power
100 watts per channel minimum RMS, all channels
driven, at 6 from 40 Hz to 20 kHz with no more
than 0.9% total harmonic distortion. (FTC)
(Europe and U.K.)
Rated output power (DIN)
(1 kHz, 0.7 % T.H.D., at 6 ) ............ 70 W + 70 W
Effective output power
(1 kHz, 10 % T.H.D., at 6 ) ........ 100 W + 100 W
(Other countries)
Rated output power
(1 kHz, 1 % T.H.D., at 6 ) ............... 80 W + 80 W
Effective output power
(1 kHz, 10 % T.H.D., at 8 ) ........ 100 W + 100 W
Signal to noise ratio
VIDEO1/VIDEO2 .............................................. 90 dB
Input sensitivity/impedance
VIDEO1/VIDEO2
(U.S.A and Canada) ...................... 300 mV/47 k
(Other countries) .......................... 250 mV/47 k
Output level/impedance
REC OUT (VIDEO1)
(U.S.A and Canada) .......................300 mV/470
(Other countries) ...........................250 mV/470
Super woofer preout
(U.S.A and Canada) ........................... 1.8 V/3.3 k
(Other countries) ................................. 2 V/3.3 k
[Video section]
Input/ Output
(Composite) ........................................... 1 Vp-p/75
Main unit (RXD-NV500)
Enclosure ............................................. Bass-reflex type
Speaker configuration
Woofer .......................... 160 mm (6-1/2”), cone type
Tweeter................................ 25 mm (1”), dome type
Impedance ................................................................ 6
Maximum input level ............................................ 100 W
Dimensions .............................. W : 225 mm (8-7/8”)
H : 350 mm (13-3/4”)
D : 263 mm (10-3/8”)
Weight (net) ............................................ 5.0 kg(1 piece)
KENWOOD follows a policy of continuous advancements in development. For this reason specifications may be
changed without notice.
÷ Sufficient performance may not be exhibited at extremely cold locations (where water freezes).
Notes
Notes
[Tuner section]
FM tuner section
Tuning frequency range ........... 87.5 MHz ~ 108 MHz
MW (AM) tuner section
Tuning frequency range
(U.S.A and Canada) ............. 530 kHz ~ 1,700 kHz
(Europe and U.K,) ................ 531 kHz ~ 1,602 kHz
(other countories)
9 kHz step ........................ 531 kHz ~ 1,602 kHz
10 kHz step ........................ 530 kHz ~ 1,610 kHz
LW tuner section (For U.K. only)
Tuning frequency range .............. 153 kHz ~ 279 kHz
[CD player section]
Laser ..............................................Semiconductor laser
Wow and flutter............................. Unmeasurable limit
[Cassette deck section]
Track ........................................4 track, 2 channel stereo
Recording system ................................. AC bias system
(Frequency: 105 kHz)
Heads
Playback / recording head ....................................... 1
Erasing head ............................................................. 1
Motor.............................................................................. 1
Fast winding time ........................ Approx. 110 seconds
(C-60 tape)
[General]
Power consumption
(U.S.A. and Canada) ........................................ 160 W
(Other countories) ........................................... 130 W
Dimensions (Attached the remote control unit)
............................................. W : 285 mm (11-1/4”)
H : 252 mm (9-15/16”)
D : 368 mm (14-1/2”)
Weight (Include the remote control unit) ......... 8.4 kg
Speakers (LS-NV500)
NV-500
For your records
Record the serial number, found on the back of the unit, in
the spaces designated on the warranty card, and in the
space provided below. Refer to the model and serial
numbers whenever you call upon your dealer for informa-
tion or service on this product.
Model Serial Number
54


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kenwood nv 500 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood nv 500 in the language / languages: English as an attachment in your email.

The manual is 1,91 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info