586255

Kenwood Mini 1160 rapid Manual

99
Zoom out
Zoom in
Previous page
1/108
Next page
99
Problem check list
Symbols indicating a fault
• Closetheloadingdoorproperly
F3 / • Checkwaterinlethose(themachineisnotgettingenoughwater,openthetapfully)
• Inlet sieve blocked (cleaning - see P. 97)
• Turn off main switch, wait a few moments and turn back on or turn programme selector to “ “
position
F4 The water level is too high, when you switch on the machine
• Wait until the machine has stopped pumping out water, or until the water level has returned
to normal (this is announced by a “clicking” noise)
• Turn programme selector to “
“ position
• Turn off main switch on the machine
• Checkdrainagesystem(seeP.98)
• Turn on main switch
• Turn programme selector to spin programme P7 (water remaining in the machine will be
pumped out) or carry out emergency draining - see P. 98
• start the programm
• If the same fault occurs again
-->Turnoffcoldtap,andremoveplugfromsocket;Contactyourcustomerservice,carryout
emergency draining (see P. 98), use emergency door opener (see P. 98) to remove washing
from machine.
F2 The washing solution is discharged very slowly, or not at all
• Turn off main switch
• Cleandrainpump(seeP.98)
• Checkdrainhoseforblockage
• Turn on main switch
• If this procedure has cured fault F2, it is possible that fault F4 may arise due to water level in
the machine being too high, this can be eliminated by carrying out procedure as described in
F4.
• start the programm
• If fault F2 occurs again
-->Turnoffcoldtap,andremoveplugfromsocket;Contactyourcustomerservice,carryout
emergency draining (see P. 98), use emergency door opener (see P. 98) to remove washing
from machine.
Should the display show the following error codes: F1, F5 - F8, F0, F II, FC they can be deleted as
mentioned below:
• Turn on main switch
• Programm timer to P2 °C
• Press button
and simultaneously until the display shows “00” (approx. 3 sec)
You can restart the washing machine now.
Attention: If the display shows one of these error codes again, please contact your customer ser-
vice, carry out emergency draining and use emergency door opener if necessary to remove was-
hing (see P. 98).
Summary only featured on the Mini 1160 rapid The water protection device has been activated!
• Turnoffcoldlltap
• Turn off main switch
• Contactyourcustomerservice,carryoutemergencydraininganduseemergencydooropenerif
necessary to remove washing (see P. 98).
… 99 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kenwood Mini 1160 rapid at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood Mini 1160 rapid in the language / languages: English, German, French, Italian as an attachment in your email.

The manual is 4,52 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info