630882

Kenwood MG700 series Manual

7
Zoom out
Zoom in
Previous page
1/108
Next page
to assemble
1 Fit the scroll inside the mincer body.
2 Fit the cutter – cutting side
outermost . Ensure it’s seated
properly – otherwise you
could damage your mincer.
3 Fit a mincer screen . Put the notch
over the pin.
●
Use the fine screen for raw meat;
fish; small nuts; or cooked meat for
shepherd’s pie or meat loaves.
●
Use the medium and coarse screens
for raw meat; fish and nuts.
4 Loosely fit the ring nut.
to use the mincer
1 With the mincer attachment in the
position shown , locate in the
outlet. Rotate the mincer body so
that the feed tube is upright.
2 Tighten the ring nut firmly by hand.
●
If you experience poor results when
mincing meat, switch off and unplug
the machine. Dismantle and clean
the attachment, then re-assemble
the attachment and refit to the
power unit. Tighten the ring nut
using the spanner provided .
3 Fit the tray. Put the dish/cover under
the mincer to catch the food.
4 Thaw frozen food thoroughly
before mincing. Cut meat into
2.5cm (1”) -wide strips.
5 Switch to speed 2. Using the pusher,
gently push the food down the feed
tube, one piece at a time. Don’t
push hard – you could damage
your mincer.
Note:
Speed 1 is for extruding sausages,
kebbe and for use with the optional
attachments.
●
If the machine stalls or overheats
during use, it will stop mincing and
emit a quiet humming noise. In the
case of a stall, switch the machine
off, then turn the control to R (reverse)
for a few seconds to release the
clogged food. Switch off and unplug
the machine and remove any clogged
material. However, if the machine
overheats, switch the machine off and
allow it to cool down for 1 hour
before continuing the mincing
operation.
●
When selecting reverse, always wait
until the machine stops operating
before turning the speed control to
the reverse (R) position.
6 Switch off and unplug after use.
7 Loosen the ring nut. If necessay use
the spanner provided.
8 Move the locking lever towards the
back of the unit, then rotate the feed
tube towards the front of the
machine, then pull free.
5
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kenwood MG700 series at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood MG700 series in the language / languages: All languages as an attachment in your email.

The manual is 0,93 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info