455522
28
Zoom out
Zoom in
Previous page
1/32
Next page
28
Other
Resetting the Microcomputer
If the microcomputer may malfunction (unit cannot be operated, or shows an
erroneous display) if the power cord is unplugged while the power is ON, or
due to some other external factor. If this happens, execute the following
procedure to reset the microcomputer and return the unit to its normal
operating condition. Please note that resetting the microcomputer will clear the contents
of the memory and returns the unit to the state it was in when it left the
factory.
In case of difficulty
Amplifier
Cause
The speaker cords are disconnected.
VOLUME is set to the minimum position.
MUTE is ON.
The SPEAKERS switches are set to OFF.
Speaker cords are short-circuited.
The speaker cord is disconnected.
The surround speaker cords and/or the center
speaker cord is disconnected.
A surround mode has not been engaged.
The surround and/or center volume controls are
set to the minimum level.
The audio cord from the turntable is not con-
nected to the PHONO jacks.
The turntable is not grounded.
• There are many possible causes for this prob-
lem, depending on the type of DVD player used.
• The input mode is set to digital manual.
• The software is copy-guarded.
• The model does not incorporate a DTS decoder.
Remedy
• Connect them properly referring to “Connecting
the speakers” #
Adjust the volume to a proper level.
Turn OFF the MUTE. *
Set the SPEAKERS switch(es) to ON. ^
Turn the power off, eliminate the short-circuit-
ing, then turn on the power again.
• Connect it properly referring to “Connecting the
speakers”. #
• Connect it properly referring to “Connecting the
speakers”. #
Select a surround mode.
Adjust the speaker levels using the test tone.
%
Insert the audio cord plugs securely into the
PHONO jacks.
Connect the grounding wire to the GND termi-
nal on the rear panel.
• Set the input mode to digital manual before
starting playback of the Dolby Digital source.
0
• Press the INPUT MODE key to select to digital
auto mode. 0
Copy-guarded video software cannot be re-
corded.
DTS sources cannot be reproduced with a model
that does not incorporate a DTS decoder.
Tuner
Cause
No antenna is connected.
The broadcast band is not set properly.
The frequency of the desired station is not
tuned.
Noise due to ignition noise from an automobile.
Noise due to interference from an electric appli-
ance.
Noise due to a nearby TV set.
The preset station belongs to a frequency that
cannot be received.
The preset memory was cleared because the
power cord had been unplugged for a long
period of time.
Remedy
Connect an antenna. !
Set the broadcast band properly.
Tune the frequency of the desired station.
)
Install the outdoor antenna away from the road.
Turn off the power to the appliance.
Install the receiver farther away from the TV.
Preset a station with a receivable frequency.
Preset the station again.
Symptom
Radio stations cannot be received.
Interference.
A station which was preset cannot be received by
pressing the corresponding numeric key.
Symptom
No sound from the speakers.
The standby indicator blinks and sound is not output.
Sound is not output from one of the speakers.
Sound is not output from the surround
speakers and / or the center speaker, or their sound is
very small.
A humming noise is generated when the PHONO
input selector is selected.
When playing a Dolby Digital (AC-3) source signal
using a DVD player, the sound is cut off soon after it
starts.
No sound is produced during playback from a DVD
player.
A video source cannot be recorded normally.
No audio is produced when a DTS source is played.
(except for KRF-7030D)
With the power cord plugged in, turn the POWER key OFF. Then,
while holding down the ON/STANDBY key, press POWER.
28


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kenwood KRF-V5030D at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood KRF-V5030D in the language / languages: English as an attachment in your email.

The manual is 0,76 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kenwood KRF-V5030D

Kenwood KRF-V5030D User Manual - German - 28 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info