465257
29
Zoom out
Zoom in
Previous page
1/40
Next page
English
|
29
Installation Procedure
Installation Procedure
1. To prevent a short circuit, remove the key from the
ignition and disconnect the - battery.
2. Make the proper input and output wire
connections for each unit.
3. Connect the wiring harness wires in the following
order: ground, battery, ignition.
4. Connect the wiring harness connector to the unit.
5. Install the unit in your car.
6. Reconnect the - battery.
2WARNING
If you connect the ignition wire (red) and the battery wire
(yellow) to the car chassis (ground), you may cause a short
circuit, that in turn may start a fire. Always connect those
wires to the power source running through the fuse box.
¤
Do not install the controller and display unit on the surface
where your vision is blocked and driving interfered.
Before installation, check that no fuel tank, pipe, nor wire
exists at backside of the mounting surface, to prevent
screws from penetrating into such component.
Mounting and wiring this product requires skills and
experience. For safetys sake, leave the mounting and wiring
work to professionals.
Make sure to ground the unit to a negative 12V DC power
supply.
Do not install the unit in a spot exposed to direct sunlight
or excessive heat or humidity. Also avoid places with too
much dust or the possibility of water splashing.
Do not use your own screws. Use only the screws provided.
If you use the wrong screws, you could damage the unit.
If your cars ignition does not have an ACC position, connect
the ignition wires to a power source that can be turned on
and off with the ignition key. If you connect the ignition
wire to a power source with a constant voltage supply, as
with battery wires, the battery may die.
If the fuse blows, first make sure the wires aren’t touching
to cause a short circuit, then replace the old fuse with one
with the same rating.
Insulate unconnected wires with vinyl tape or other similar
material. To prevent a short circuit, do not remove the caps
on the ends of the unconnected wires or the terminals.
After the unit is installed, check whether the brake lamps,
blinkers, wipers, etc. on the car are working properly.
Installation for Display Unit
Installation location and cleaning
Select for installation a location where the stand can
be placed completely horizontal shown in Figure A.
Do not install in locations where the entire support is
at a diagonal such as in Figure B or where the display
unit is facing down such as in Figure C.
A
B
C
¤
Thoroughly wipe away and dust or grease from the
installation location using a cloth which has been soaked in
a neutral cleaning agent and wrung out. Attach the stand
after allowing the installation location to dry.
Do not attach the double-sided tape more than once or
touch the adhesive with your fingers as this will weaken its
adhesive strength.
If the temperature of the surface of the installation location
is low, warm it up using a heater or other means before
attaching the stand. Low temperature may weaken the
adhesive strength of the tape.
The supplied stand is specially intended for this product. Do
not use it with another display.
29


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kenwood KOS-A210 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood KOS-A210 in the language / languages: English as an attachment in your email.

The manual is 0,79 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kenwood KOS-A210

Kenwood KOS-A210 User Manual - German - 40 pages

Kenwood KOS-A210 User Manual - Dutch - 40 pages

Kenwood KOS-A210 User Manual - French - 40 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info