565287
18
Zoom out
Zoom in
Previous page
1/58
Next page
16
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
INSTALLATION / CONNECTION
Warning
The unit can only be used with a 12V DC power supply, negative ground.
Disconnect the battery’s negative terminal before wiring and mounting.
Do not connect Battery wire (yellow) and Ignition wire (red) to the car chassis or
Ground wire (black) to prevent a short circuit.
Insulate unconnected wires with vinyl tape to prevent a short circuit.
Be sure to ground this unit to the car’s chassis again after installation.
Caution
For safety’s sake, leave wiring and mounting to professionals. Consult the car audio
dealer.
Install this unit in the console of your vehicle. Do not touch the metal parts of this
unit during and shortly after use of the unit. Metal parts such as the heat sink and
enclosure become hot.
Do not connect the
[
wires of speakers to the car chassis or Ground wire (black), or
connect them in parallel.
Mount the unit at an angle of less than 30º.
If your vehicle wiring harness does not have the ignition terminal, connect Ignition
wire (red) to the terminal on the vehicle’s fuse box which provides 12 V DC power
supply and is turned on and off by the ignition key.
After the unit is installed, check whether the brake lamps, blinkers, wipers, etc. on
the car are working properly.
If the fuse blows, first make sure the wires are not touching car’s chassis, then replace the
old fuse with one that has the same rating.
Basic procedure
1
Remove the key from the ignition switch, then disconnect
the
[
terminal of the car battery.
2 Connect the wires properly.
See Wiring connection.
( 17, 18)
3 Install the unit to your car.
See Installing the unit (in-dash mounting).
4 Connect the
[
terminal of the car battery.
5 Reset the unit.
( 3)
Do the required wiring.
( 17, 18)
Dashboard of your car
Bend the appropriate tabs to hold
the mounting sleeve firmly in place.
How to remove the unit
1
Detach the faceplate.
2 Fit the catch pin on the
extraction keys into the holes on
both sides of the trim plate, then
pull it out.
3 Insert the extraction keys deeply
into the slots on each side, then
follow the arrows as shown on
the right.
Installing the unit (in-dash mounting)
Hook on the top side
Orientate the trim
plate as illustrated
before fitting.
JS_KWD_KMM_BT34_EWE0_01_EN.indd 16JS_KWD_KMM_BT34_EWE0_01_EN.indd 16 7/11/2013 12:55:02 PM7/11/2013 12:55:02 PM
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kenwood KMR-M308BTE at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood KMR-M308BTE in the language / languages: English, German as an attachment in your email.

The manual is 1,09 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kenwood KMR-M308BTE

Kenwood KMR-M308BTE User Manual - German - 19 pages

Kenwood KMR-M308BTE User Manual - Dutch - 19 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info