536433
9
Zoom out
Zoom in
Previous page
1/220
Next page
pprroobblleemm
The whisk or K-beater knocks against the bottom of the bowl or isn’t
r
eaching the ingredients in the bottom of the bowl.
solution
Adjust the height using the spanner provided. Here’s how:
1 Unplug the appliance.
2 Raise the mixer head and insert the whisk or beater.
3 L
ower the mixer head. If the clearance needs to be adjusted, raise the
mixer head and remove the tool. Ideally the whisk and K-beater should be
almost touching the bottom of the bowl
.
4 Using the spanner provided loosen the nut sufficiently to allow
a
djustment of the shaft
.
To lower the tool closer to the bottom of the
b
owl, turn the shaft anti-clockwise. To raise the tool away from the bottom
of the bowl turn the shaft clockwise.
5 Re-tighten the nut.
6 Fit the tool to the mixer and lower the mixer head. (Check its position see
p
oints above).
7 Repeat the above steps as necessary until the tool is set correctly. Once
this is acheived tighten the nut securely.
problem
The mixer stops during operation.
solution
Your mixer is fitted with an overload protection device and will stop if
overloaded to protect the machine. If this happens, unplug the mixer.
Remove some of the ingredients to reduce the load, and allow the
mixer to stand for a few minutes. Plug in and press the start/stop
button. If the mixer does not restart immediately allow to stand for
additional time.
If for any reason power to the mixer is interrupted and the machine
stops working, switch off by pressing the start/stop button, wait a few
seconds and then switch on again. The mixer should resume operating
straight away.
to fit and use your splashguard
1 Raise the mixer head until it locks.
2 Fit the bowl onto the base.
3 Push the splashguard onto the underside of the mixer head until
fully located. The hinged section should be positioned as shown.
4 Insert required tool.
5 Lower the mixer head.
During mixing, ingredients can be added directly to the bowl via the
hinged section of the splashguard
.
You do not need to remove the splashguard to change tools.
troubleshooting
9
m
i
n
1
2
3
4
P
m
i
n
s
e
c
m
i
n
1
2
3
4
5
6
P
m
i
n
s
e
c
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kenwood KMM040 Major Titanium met Timer at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood KMM040 Major Titanium met Timer in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 11,94 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info