565291
14
Zoom out
Zoom in
Previous page
1/15
Next page
12
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
INSTALLATION / CONNECTION
Warning
The unit can only be used with a 12V DC power supply, negative
ground.
Disconnect the battery’s negative terminal before wiring and
mounting.
Do not connect Battery wire (yellow) and Ignition wire (red) to
the car chassis or Ground wire (black) to prevent a short circuit.
Insulate unconnected wires with vinyl tape to prevent a short
circuit.
Be sure to ground this unit to the car’s chassis again after
installation.
Caution
For safety’s sake, leave wiring and mounting to professionals.
Consult the car audio dealer.
Install this unit in the console of your vehicle. Do not touch the
metal parts of this unit during and shortly after use of the unit.
Metal parts such as the heat sink and enclosure become hot.
Do not connect the
[
wires of speakers to the car chassis or
Ground wire (black), or connect them in parallel.
Mount the unit at an angle of less than 30º.
If your vehicle wiring harness does not have the ignition
terminal, connect Ignition wire (red) to the terminal on the
vehicle’s fuse box which provides 12 V DC power supply and is
turned on and off by the ignition key.
After the unit is installed, check whether the brake lamps,
blinkers, wipers, etc. on the car are working properly.
If the fuse blows, first make sure the wires are not touching car’s
chassis, then replace the old fuse with one that has the same rating.
Basic procedure
1
Remove the key from the ignition switch, then
disconnect the
[
terminal of the car battery.
2 Connect the wires properly.
See Wiring connection.
( 13)
3 Install the unit to your car.
See Installing the unit (in-dash mounting).
4 Connect the
[
terminal of the car battery.
5 Reset the unit.
( 3)
Do the required wiring.
( 13)
Dashboard of
your car
Bend the appropriate tabs to hold
the mounting sleeve firmly in place.
How to remove the unit
1
Detach the faceplate.
2 Fit the catch pin on the
extraction keys into the
holes on both sides of the
trim plate, then pull it out.
3 Insert the extraction keys
deeply into the slots on
each side, then follow the
arrows as shown on the
right.
Installing the unit (in-dash mounting)
Hook on the top side
Orientate the trim
plate as illustrated
before fitting.
Part list for
installation
(A)
Faceplate
(C)
Mounting sleeve
(B)
Trim plate
(D)
Wiring harness
(E)
Extraction key
EN_KMM_361SD_001A_EN_f.indd 12EN_KMM_361SD_001A_EN_f.indd 12 11/10/2013 9:21:06 AM11/10/2013 9:21:06 AM
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kenwood KMM-100AY at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood KMM-100AY in the language / languages: English as an attachment in your email.

The manual is 0,35 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kenwood KMM-100AY

Kenwood KMM-100AY User Manual - German - 13 pages

Kenwood KMM-100AY User Manual - Dutch - 13 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info