Manual Kenwood KM288 (page 8 of 162) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

527135

Zoom out

Zoom in

1/162

Food Processor AT284 (if supplied)

Use the food processing attachment to chop, slice, shred and rasp. The citrus

juicer attachment (if supplied) can be used to juice citrus fruit and can only be

used with the AT284 food processor.

important

When removing the packaging, ensure the plastic blade cover is removed

from the knife blade. Take care the blades are very sharp. The cover

should be discarded as it is to protect the blade during manufacture and

transit only.

safety

●

The blades and discs are very sharp, handle with care. Always hold the

knife blade by the finger grip at the top, away from the cutting

edge, both when handling and cleaning.

●

Always remove the knife blade before pouring contents from the bowl.

●

Keep hands and utensils out of the processor bowl whilst connected to the

power supply.

●

Never use your fingers to push food down the feed tube. Always use the

pusher/s supplied.

●

Before removing the lid from the bowl or the attachment from the power

unit:-

●●

switch off;

●●

wait until the blades/discs have completely stopped;

●

When slicing/shredding or rasping don’t let the bowl fill up as far as the

cutting disc: empty it regularly.

●

Should excessive vibration occur when using this attachment, either reduce

the speed or stop the machine and remove some of the contents.

●

This machine will be damaged and may cause injury if the

interlock mechanism is subjected to excessive force.

key ቲ & ታ

food processor

ቢ pushers: large and small

ባ feed tube

ቤ food processor lid

ብ finger grip

ቦ knife blade

ቧ food processor bowl

ቨ drive shaft

ቩ thick slicer/shredder disc

ቪ thin slicer/shredder disc

ቫ rasping disc

optional discs

ቭ thin (julienne style) chipper disc

ቮ standard chipper disc

ቯ extra coarse shredding disc

citrus juicer

ተ cone

ቱ sieve

Not all of the above parts will necessarily be included in pack. Contents are

dependent upon model variant.

knife blade

Use the knife blade to chop raw and cooked meat, cooked eggs,

vegetables, nuts, pâtés and dips and to also make crumbs from bread and

biscuits.

to use the knife blade

1 Remove the medium speed outlet cover by lifting off

ᕡ

Place the drive shaft onto the outlet

ᕢ

3 Fit the bowl over the drive shaft with the handle above the on/off and speed

switch and turn clockwise until it locks into position

ᕣ

4 Fit the knife blade over the drive shaft and turn until it drops all the way down.

The knife blade is very sharp always handle with care.

5 Cut the food up and place into the bowl ensuring that it is evenly distributed.

6 Fit the lid, feed tube above the speed switch and turn clockwise ensuring

that the tab on the lid slots into the groove in the bowl handle

ᕤ

. When

correctly fitted the markings should align .

●

The attachment will not operate if it is incorrectly assembled

or incorrectly fitted to the kitchen machine or if the high

speed outlet cover is not fitted.

7 Fit the pushers.

8 Switch on and process until the desired consistency is achieved. We

recommend a high speed for most chopping functions.

●

Use the pulse for short burst of power. The pulse will operate for as long

as the switch is held in position.

9 Switch off and unplug.

10 Remove the attachment.

11 Refit the medium speed outlet cover after use.

hints

●

Cut food up before placing into the bowl. Meat, bread, vegetables and other

foods of a similar texture should be cut into cubes approximately 2cm/3⁄4 in.

Biscuits should be broken into pieces and added down the feed tube whilst

the machine is operating.

●

Herbs are best chopped when clean and dry.

●

Don’t blend liquid ingredients as they may leak from around the lid. A

blender is available for this purpose. However, when puréeing soups etc.,

drain solids, blend and then return to the liquid.

●

Take care not to over process when using the knife blade.

●

Don’t use the knife blade to mix heavy loads such as bread dough otherwise

you may damage the mixer. Use the dough hook in the mixing bowl to make

bread and the beater in the bowl to make cakes and pastry.

●

Don’t use the knife blade to chop ice cubes or other hard foods, such as

spices, they may damage the attachment.

●

If adding almond essence or flavouring to mixtures avoid contact with the

plastic as this may result in permanent marking.

maximum capacity

●

meat 400g (14oz)

Make ‘mince’ by trimming raw meat of any excess fat and cutting into

2 cm/

⁄4 in cubes, place into the processor bowl and operate for

approximately 20 seconds or until the desired texture is achieved. The longer

you run the machine the smoother the texture will be.

slicer/shredder and rasping disc

Use the slicer/shredder to slice or shred fruit, vegetables and cheese and

the rasping disc for grating Parmesan cheese and potato for German potato

dumplings.

to use the slicer/shredder/rasper

what the cutting discs do

slicer/shredders

Discs ቩ and ቪ are reversible: one side slices, the other side shreds. You

can slice cheese, carrot, potato, cabbage, cucumber, courgette, beetroot,

onion. You can shred cheese, carrot, potato and foods of a similar texture.

Your chosen cutting side must be uppermost.

rasping disc ቫ grates parmesan cheese and potato for German potato

dumplings.

optional discs

thin (julienne style) chipper ቭ

This disc cuts potatoes for Julienne style French fries and firm ingredients for

salads, garnishes, casseroles and stir fries (eg carrot, swede, courgette and

cucumber).

standard chipper ቮ cuts potatoes for thin French fries and firm

ingredients for salads and dips (eg swede, cucumber).

extra coarse shredder ቯ coarsely shreds cheese and carrot.

using the cutting discs

1 Remove the medium speed outlet cover by lifting off.

2 Place the drive shaft onto the outlet.

3 Fit the bowl over the drive shaft with the handle above the on/off and speed

switch and turn clockwise until it locks into position.

4 Place the cutting disc onto the drive shaft. Your chosen cutting side must be

uppermost. Handle the cutting discs with care - they are

extremely sharp. Hold the discs by the centre grip.

5 Fit the lid, feed tube above the speed switch and turn clockwise ensuring

that the tab on the lid slots into the groove in the bowl handle. When

correctly fitted the markings should align .

●

The attachment will not operate if it is incorrectly assembled

or incorrectly fitted to the kitchen machine or if the high

speed outlet cover is not fitted.

6 Choose which feed tube you want to use. The pusher contains a smaller

feed tube for processing individual items or thin ingredients.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood KM288 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,73 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Kenwood KM288 Manual

Product: