463528
11
Zoom out
Zoom in
Previous page
1/19
Next page
12
display
For your safety the mixer is fitted with 5 separate safety sensors which will operate when using the mixer in the
cooking mode. If the mixer is switched on and a safety sensor activated, the timer/temperature display will show
a
n error message e.g. ‘E:01’. This will be accompanied by a beeping sound and the mixer will not work. Check
t
he following error messages:-
If these or any other error codes continue to appear on the display contact Kenwood Customer Care.
to use the countdown timer
The timer can be used in both the cooking and non cooking modes. If a countdown time is not selected, the
timer will automatically count up in 1 second intervals whilst the mixer is in operation. The maximum running time
is 3 hours.
1 Connect the mixer to the power supply. The display will briefly show and then clear leaving the power on
indicator visible .
2 Press either the + or button and 0:00 will appear in the display.
3 Press either the + or button until the desired time is displayed. The timer will count up in 5 second intervals. If
the button is pressed continuously the numbers will change more quickly the longer it is held down. A maximum
time of 3 hours can be set.
Note: If the + button is pressed when the timer is at 3:00 the displayed time will change to 0:00. If the button is
pressed when the timer is at 0:00 the displayed time will change to 3:00.
4 Turn the speed control to the desired speed, the mixer will start and the timer will count down in 1 second
intervals.
The mixer operation can be paused at any time by turning the speed control to the off ‘O’ position. This will also
pause the timer. The timer will continue to count down when the mixer is re-started.
5 The mixing process will automatically stop when the total time has elapsed and audible beeps will be emitted for
3 seconds. The display will flash for 5 seconds and then clear showing the power on indicator .
to reset the timer
1 Zero the timer by pressing the + and buttons at the same time (the speed control must be in the off ‘O’ position).
If the machine has been idle for 10 minutes, the LCD display and backlight will enter ‘sleep mode and all the
displays will turn off. If any button or control knob is activated, the display will resume its previous format.
Error Message Description Solution
The head of the machine is in the raised position. Close the head. Turn the speed control
When the head is lifted, a safety sensor disables to the ‘O’ position and then select the
E:01
t
he motor and heater. If the speed control is desired speed.
turned to any setting other than the Off ‘O’
position when the head is raised, this message
is displayed and the motor will not switch on.
T
he Cooking Chef Bowl is not fitted. The heating Ensure that the Cooking Chef bowl is
function will only work if the Cooking bowl is being used. Check that the bowl
E:02 being used. This bowl must also be correctly is fitted correctly. Turn the speed
fitted. Safety sensors will detect an incorrect control to “0” and then select desired
bowl or the correct bowl incorrectly fitted. speed.
The heat shield is not fitted. The heating function Ensure the heat shield is fitted
E:03 will be disabled if the heat shield is not correctly correctly. Turn the speed control to ‘O’
fitted. and then select desired speed.
T
he slow speed outlet and high speed/medium Ensure that all covers are fitted correctly.
s
peed outlet covers are not fitted. These covers Turn the speed control to ‘O’ and then
are fitted with safety sensors. If the covers are select desired speed.
E:04 not fitted correctly the heating will switch off and
if stir functions are selected, the motor will run
continuously. Mixing speeds min to max will
run continuously.
Temperature sensor problem. If the heater Turn the speed control to ‘O’, unplug the
control detects a bowl temperature higher than machine and allow to cool. Check
E:09 expected during normal use, the motor and that the bowl base and temperature
heater will automatically switch off. sensors are clean. Replace plug and
switch on as normal.
Motor speed or overheat problem. If the motor Turn the speed control to ‘O’ and unplug
E:10
stalls or gets too hot, the control system will the machine. Remove any obstructions
automatically switch off the motor and heater. causing the motor to stall. Ensure all
the air vents are clear of obstructions.
Plug in and switch on.
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kenwood KM070 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood KM070 in the language / languages: English as an attachment in your email.

The manual is 0,75 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kenwood KM070

Kenwood KM070 User Manual - German, Dutch, French, Italian, Portuguese, Spanish - 164 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info