36090
4
Zoom out
Zoom in
Previous page
1/40
Next page
— 4 —
English
Safety precautions
To prevent injury or fire, take the
following precautions:
When extending the ignition, battery, or
ground wires, make sure to use automotive-
grade wires or other wires with a 0.75mm
2
(AWG18) or more to prevent wire
deterioration and damage to the wire
coating.
•To prevent a short circuit, never put or leave
any metallic objects (such as coins or metal
tools) inside the unit.
If the unit starts to emit smoke or strange
smells, turn off the power immediately and
consult your Kenwood dealer.
To prevent damage to the unit, take
the following precautions:
Make sure to ground the unit to a negative
12V DC power supply.
Do not open the top or bottom covers of the
unit.
Do not install the unit in a spot exposed to
direct sunlight or excessive heat or humidity.
Also avoid places with too much dust or the
possibility of water splashing.
When replacing a fuse, only use a new one
with the prescribed rating. Using a fuse with
the wrong rating may cause your unit to
malfunction.
•To prevent a short circuit when replacing a
fuse, first disconnect the wiring harness.
2CAUTION
2WARNING
Do not use your own screws. Use only the
screws provided. If you use the wrong
screws, you could damage the unit.
If you experience problems during
installation, consult your Kenwood dealer.
The illustrations of the display and the panel
appearing in this manual are examples used
to explain more clearly how the controls are
used. Therefore, what appears on the display
in the illustrations may differ from what
appears on the display on the actual
equipment, and some of the illustrations on
the display may represent something
impossible in actual operation.
The marking of products using lasers
(Except for some areas)
The label is attached to the chassis/case and
says that the component uses laser beams
that have been classified as Class 1. It
means that the unit is utilizing laser beams
that are of a weaker class. There is no
danger of hazardous radiation outside the
unit.
CLASS 1
LASER PRODUCT
NOTE
IMPORTANT INFORMATION
You can enjoy a DVD with this unit alone when
connecting it to an external monitor or audio
equipment.
Also, you can operate this unit connected to a
center unit made by Kenwood to output
sound.
A Kenwood-made center unit that can be
connected to this unit is called “Center Unit”.
About a center unit that can be
connected to this unit:
If a center unit (such as CD receivers) has
capability for “N” of <“O-N” switch>, this unit
can be connected to this unit.
According to the operating instructions of a
center unit, the setting of <“O-N” switch> is
“N”. This unit is, however, exclusive to “N”.
Therefore, <“O-N” switch> is unnecessary.
If using a separate CD/MD changer switching
unit “KCA-S210A”, you can connect this unit
to a center unit with disc changer control that
has no capability for “N”.
See the operating instructions attached to
KCA-S210A for details of connection.
The functions available and/or information
displayable may depend on types of units to
which you connect.
KDV-C810_U.S 02.2.15 10:56 AM Page 4
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kenwood KDV-C840 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood KDV-C840 in the language / languages: English as an attachment in your email.

The manual is 0,94 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info