667460
22
Zoom out
Zoom in
Previous page
1/68
Next page
22
|
KDC-X492/KDC-MP438U/KDC-MP408U/KDC-MP338
Troubleshooting Guide
The messages shown below display your
systems condition.
TOC ERROR: No disc has been loaded in the disc
magazine.
The CD is quite dirty. The CD is upside-
down. The CD is scratched a lot.
E-05: The disc is unreadable.
E-77: The unit is malfunctioning for some reason.
Press the reset button on the unit. If the “E-
77” code does not disappear, consult your
nearest service center.
E-99: Something is wrong with the disc magazine.
Or the unit is malfunctioning for some reason.
Check the disc magazine. And then press
the reset button on the unit. If the “E-99”
code does not disappear, consult your
nearest service center.
IN (Blink): The CD player section is not operating
properly.
Reinsert the CD. If the CD cannot be
ejected or the display continues to flash
even when the CD has been properly
reinserted, please switch off the power
and consult your nearest service center.
PROTECT: The speaker wire has a short-circuit or
touches the chassis of the vehicle, and then
the protection function is activated.
Wire or insulate the speaker cable
properly and press the reset button. If
the “PROTECT code does not disappear,
consult your nearest service center.
NA FILE: An Audio file is played with a format that this
unit can’t support.
COPY PRO: A copy-protected file is played.
READ ERROR: The file system of the connected USB device
is broken.
Copy the files and folders for the USB
device again. If the error message is still
displayed, initialize the USB device or use
other USB devices.
NO DEVICE: The USB device is selected as a source
although no USB device is connected.
Change the source to any source other
than USB. Connect an USB device, and
change the source to USB again.
N/A DEVICE: An unsupported USB device is connected.
Remove the USB device without entering
the remove mode.
NO MUSIC DATA/E-15:
The connected USB device contains no
playable audio file.
Media was played that doesn’t have data
recorded that the unit can play.
USB ERROR/USB (Blink):
Some trouble may have occurred to the
connected USB device.
Remove the USB device, then cycle the
power switch to ON. If the same display is
repeated, use another USB device.Remove
the USB device without entering the
remove mode.
iPod ERROR: Connection to the iPod has failed.
Check that the connected iPod is an iPod
that is supported. See <About Audio file>
(page 16) for information on supported
iPods.
Remove the USB device and then
reconnect it.
Confirm that the software for the iPod is
the latest version.
USB REMOVE: The Remove mode has been selected for the
USB device/iPod. You can remove the USB
device/iPod safely.
B64-3955-00_English_K_r1.indd 22B64-3955-00_English_K_r1.indd 22 07.11.12 5:20:04 PM07.11.12 5:20:04 PM
22


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kenwood KDC-X492 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood KDC-X492 in the language / languages: English, French, Spanish as an attachment in your email.

The manual is 1,13 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info