Manual Kenwood KDC-X492 (page 18 of 68) (English, French, Spanish)

667460

Zoom out

Zoom in

1/68

KDC-X492/KDC-MP438U/KDC-MP408U/KDC-MP338

Accessories/ Installation Procedure

Accessories

..........1

..........2

..........4

Installation Procedure

1. To prevent a short circuit, remove the key from the

ignition and disconnect the - battery.

2. Make the proper input and output wire

connections for each unit.

3. Connect the speaker wires of the wiring harness.

4. Connect the wiring harness wires in the following

order: ground, battery, ignition.

5. Connect the wiring harness connector to the unit.

6. Install the unit in your car.

7. Reconnect the - battery.

8. Press the reset button.

2WARNING

If you connect the ignition wire (red) and the battery wire

(yellow) to the car chassis (ground), you may cause a short

circuit, that in turn may start a fire. Always connect those

wires to the power source running through the fuse box.

• Mounting and wiring this product requires skills and

experience. For safety’s sake, leave the mounting and wiring

work to professionals.

• Make sure to ground the unit to a negative 12V DC power

supply.

• Do not install the unit in a spot exposed to direct sunlight

or excessive heat or humidity. Also avoid places with too

much dust or the possibility of water splashing.

• Do not use your own screws. Use only the screws provided.

If you use the wrong screws, you could damage the unit.

• If the power is not turned ON (“PROTECT” is displayed),

the speaker wire may have a short-circuit or touched the

chassis of the vehicle and the protection function may

have been activated. Therefore, the speaker wire should be

checked.

• If your car’s ignition does not have an ACC position, connect

the ignition wires to a power source that can be turned on

and off with the ignition key. If you connect the ignition

wire to a power source with a constant voltage supply, as

with battery wires, the battery may die.

• If the console has a lid, make sure to install the unit so that

the faceplate will not hit the lid when closing and opening.

• If the fuse blows, first make sure the wires aren’t touching

to cause a short circuit, then replace the old fuse with one

with the same rating.

• Insulate unconnected wires with vinyl tape or other similar

material. To prevent a short circuit, do not remove the caps

on the ends of the unconnected wires or the terminals.

• Connect the speaker wires correctly to the terminals to

which they correspond. The unit may be damaged or fail to

work if you share the - wires or ground them to any metal

part in the car.

• When only two speakers are being connected to the

system, connect the connectors either to both the front

output terminals or to both the rear output terminals (do

not mix front and rear). For example, if you connect the +

connector of the left speaker to a front output terminal, do

not connect the - connector to a rear output terminal.

• After the unit is installed, check whether the brake lamps,

blinkers, wipers, etc. on the car are working properly.

• Mount the unit so that the mounting angle is 30° or less.

About CD players/disc changers connected

to this unit

Kenwood disc changers/ CD players released in 1998

or later can be connected to this unit.

Refer to the catalog or consult your Kenwood dealer

for connectable models of disc changers/ CD players.

Note that any Kenwood disc changers/ CD players

released in 1997 or earlier and disc changers made by

other makers cannot be connected to this unit.

Connecting unsupported disc changers/CD players to

this unit may result in damage.

Set the “O-N” Switch to the “N” position for the

applicable Kenwood disc changers/ CD players.

The functions you can use and the information that

can be displayed may differ depending on the models

being connected.

B64-3955-00_English_K_r1.indd 18B64-3955-00_English_K_r1.indd 18 07.11.12 5:20:02 PM07.11.12 5:20:02 PM

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood KDC-X492 in the language / languages: English, French, Spanish as an attachment in your email.

The manual is 1,13 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Kenwood KDC-X492 Manual

Product: