41271
62
Zoom out
Zoom in
Previous page
1/67
Next page
62
|
English
Troubleshooting Guide
What might seem to be a malfunction in your unit
may just be the result of slight misoperation or
miswiring. Before calling service, first check the
following table for possible problems.
General
? The power does not turn ON.
The fuse has blown.
After checking for short circuits in the wires,
replace the fuse with one with the same
rating.
Speaker cable touches on chassis etc.
Wire or insulate the speaker cable properly
and press the reset button.
The Demonstration mode has been selected.
Hold down button [5] and press the Reset
button to release the Demonstration mode.
? Theres a source you can’t switch.
Theres no media inserted.
Set the media you want to listen to. If theres
no media in this unit, you can’t switch to each
source.
The Disc changer isn’t connected.
Connect the Disc changer. If the Disc changer
isn’t connected to its input terminal, You can’t
switch to an external disc source.
? The memory is erased when the ignition is
turned OFF.
The ignition and battery wire are incorrectly
connected.
Connect the wire correctly, referring to the
section on 'Connecting Wires to Terminals'.
? Theres no loudness effect.
The 'System Q' (KDC-W8027) (page 20) is set to
SRS WOW.
Turn it to the other items.
? The TEL mute function does not work.
The TEL mute wire is not connected properly.
Connect the wire correctly, referring to the
section on 'Connecting Wires to Terminals'.
? The TEL mute function turns ON even though the
TEL mute wire is not connected.
The TEL mute wire is touching a metal part of the
car.
Pull the TEL mute wire away from the metal
part of the car.
? Even if Loudness is turned ON, high-pitched tone
isn’t compensated for.
Tuner source is selected.
High-pitched tone isn’t compensated for when
in Tuner source.
The 'System Q' (KDC-W8027) (page 20) is set to
SRS WOW.
Turn it to the other items.
? The Bass center frequency, Bass quality factor,
Bass extend, Middle center frequency, Middle
quality factor, and Treble center frequency can’t
be adjusted.
The 'System Q Setting' (page 50) is set OFF.
Set it ON.
? No sound can be heard, or the volume is low.
The fader or balance settings are set all the way to
one side.
Center the fader and balance settings.
The input/output wires or wiring harness are
connected incorrectly.
Reconnect the input/output wires or the
wiring harness correctly. See the section on
'Connecting Wires to Terminals'.
The values of Volume offset are low.
Turn up the Volume offset, referring to the
section on 'Audio Control' (KDC-W8027) (page
22)/ 'Audio control' (KDC-PSW9527/W9027)
(page 26).
The 'Built-in Amp Mute Setting' (page 50) is ON.
Turn it OFF.
If the PLII is selected by 'Audio Setup (Easy mode)'
(KDC-PSW9527/W9027) (page28) and if the Front
speaker is set to "16 — 710" and the Center
speaker is set to "16 over," the subwoofer does not
sound.
---
? The sound quality is poor or distorted.
One of the speaker wires is being pinched by a
screw in the car.
Check the speaker wiring.
The speakers are not wired correctly.
Reconnect the speaker wires so that each
output terminal is connected to a different
speaker.
? Subwoofer Output, Subwoofer Low Pass Filter
and Subwoofer setting can’t be done.
The 'Dual Zone System' (page 24) is ON.
Turn it OFF.
? The Touch Sensor Tone doesn’t sound.
The preout jack is being used.
The Touch Sensor Tone can’t be output from
the preout jack.
? Even though Synchronize Clock is ON, the clock
can’t be adjusted.
The received RDS station isn’t sending time data.
Receive another RDS station.
? The Dimmer function doesn’t work.
The Dimmer wire isn’t connected correctly.
Check the Dimmer wire connection.
KDC-PSW9527(E)_U.S _r5 62 03.11.28, 11:01:09 PM
62


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kenwood KDC-W9027 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood KDC-W9027 in the language / languages: English as an attachment in your email.

The manual is 1,04 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kenwood KDC-W9027

Kenwood KDC-W9027 User Manual - German - 66 pages

Kenwood KDC-W9027 User Manual - Dutch - 66 pages

Kenwood KDC-W9027 User Manual - French - 66 pages

Kenwood KDC-W9027 User Manual - Italian - 66 pages

Kenwood KDC-W9027 User Manual - Portuguese - 66 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info