565546
12
Zoom out
Zoom in
Previous page
1/64
Next page
12
|
English
General features
Subwoofer Output
Turning the Subwoofer output ON or OFF.
Hold down on [AM] of the Control knob for at
least 1 second.
Each time you press the button, Subwoofer
output switches ON and OFF.
When it is ON, "SUBWOOFER ON" is displayed.
You can control this function when "2ZONE" of
<Audio Setup> (page 11) is set to "OFF".
You can control this item when Speaker Select
Subwoofer of <Sound Management system> (page
13) is set to any item other than "None".
Sound Field Control
1 Select the source to adjust
Press the [SRC] button.
2 Show the Multi-function display
Press the [NEXT] button repeatedly until
"S.F.C" appears.
Refer to <Notes on Multi-function System> (page
9).
3 Enter Sound Field Control mode
Turn the [VOL] knob to select "S.F.C".
Press the [VOL] knob.
To get the best sound, first set the Cabin Setting
and Speaker Select Front/Rear parameters using the
<Sound Management system> (page 13).
When "2ZONE" of <Audio Setup> (page 11) is ON, you
cannot select "S.F.C".
4 Select the Sound Field Control item to
adjust
1 Turn the [VOL] knob to select the item you
want to select. Press the [VOL] knob.
2 Press the Control knob.
3 Push the Control knob towards [FM] or
[AM].
12 3
Sound Field control item
"X'Over" "HPF Front" "fc"
"SLP"
Front High Pass Filter Frequency
Front High Pass Filter Slope
"HPF Rear"*¹ "fc"
"SLP"
Rear High Pass Filter Frequency
Rear High Pass Filter Slope
"LPF
SubWoofer"*²
"fc"
"SLP"
"Phase"
Subwoofer Low Pass Filter Frequency
Subwoofer Low Pass Filter Slope
Subwoofer Low Pass Filter Phase
"DTA" "DTA Front" DTA Front
"DTA Rear"*¹ DTA Rear
"DTA
SubWoofer"*²
DTA Subwoofer
"POSI" Position Setting
"Preset" Preset value storage/recalling
"Preset": You can store an adjusted sound control
value by selecting "Memory". Refer to
<Memory mode> (page 16). Also, you
can recall it by selecting "Recall". Refer to
<Memory Recall mode> (page 16).
You can adjust "SubWoofer" when <Subwoofer
Output> (page 12) is set to "SUBWOOFER ON".
X'Over (Crossover Network Setup)
You can manually set a crossover frequency for the
speakers.
• DTA (Digital Time Alignment)
Manually set the sound output timing of each
channel.
• *
1
You can control this item when Speaker Select Rear
of <Sound Management system> (page 13) is set to
any item other than "None".
• *
2
You can control this item when Speaker Select
Subwoofer of <Sound Management system> (page
13) is set to any item other than "None".
5 Adjust the Sound Field Control item
Push the Control knob towards [4] or
[¢].
Each time you push the knob, the setting
alternates between the settings shown in the
table below.
Sound Field Control Item Range
Front High Pass Filter Frequency/
Rear High Pass Filter Frequency
Through/30 — 100/120/150/
180/220/250 (Hz)
Front High Pass Filter Slope/
Rear High Pass Filter Slope/
Subwoofer Low Pass Filter Slope
-12/-18/-24 dB/Oct
Subwoofer Low Pass Filter
Frequency
30 — 100/120/150/180/220/
250 (Hz)/Through
Subwoofer Low Pass Filter Phase Normal/ Reverse
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kenwood KDC-PSW9531 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood KDC-PSW9531 in the language / languages: English as an attachment in your email.

The manual is 1,61 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kenwood KDC-PSW9531

Kenwood KDC-PSW9531 User Manual - German - 62 pages

Kenwood KDC-PSW9531 User Manual - Dutch - 62 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info