41267

Kenwood KDC-PS9590R Manual

50
Zoom out
Zoom in
Previous page
1/56
Next page
Free switching of the sound
quality.
The system Q function is set on Scan mode. Refer to the “System Q” page and switch it to a
function other than Scan mode. (see page 13)
The TEL mute function does
not work.
The TEL mute cable is not connected properly. Connect the cable correctly, referring to the section on
"Connecting Cables to Terminals".
The TEL mute function turns
on even though the TEL mute
cable is not connected.
The TEL mute cable is touching a metal part of the car. Pull the TEL mute cable away from the metal part of the
car.
Audio control setting cannot be
achieved.
The system Q function is set on Scan mode. Refer to the “System Q” page and switch it to a
function other than Scan mode.(see p. 13).
English
— 50 —
What might appear to be a malfunction in your unit may just be the result of slight misoperation or miswiring.
Before calling service, first check the following table for possible problems.
Troubleshooting Guide
SOLUTIONPOSSIBLE CAUSEPROBLEM
Nothing happens when the
buttons are pressed.
The computer chip in the unit is not functioning normally. Press the reset button on the unit (see page 4).
The antenna control cable is not connected. Connect the cable correctly, referring to the section on
"Connecting Cables to Terminals".
Radio reception is poor. The car antenna is not extended. Pull out the antenna all the way.
The power does not turn on. The fuse has blown. After checking for short circuits in the cables, replace
the fuse with one having the same rating.
No ACC position on vehicle ignition. Connect the same cable to the ignition as the battery cable.
The memory is erased when
the ignition is turned off.
The battery cable has not been connected to the proper
terminal.
Connect the cable correctly, referring to the section on
"Connecting Cables to Terminals".
The ignition and battery cable are incorrectly connected. Connect the cable correctly, referring to the section on
"Connecting Cables to Terminals".
If you have selected Standby
mode, the power will go OFF
automatically.
The Power Off Timer function has been activated. If you do not want the power to go OFF automatically,
cancel the Power Off Timer function.
— 50 —
The faceplate does not open or
close.
The faceplate is incorrectly attached. Reattach the faceplate correctly, See the section on
"Removing the Faceplate".(page.14)
… 50 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kenwood KDC-PS9590R at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood KDC-PS9590R in the language / languages: English as an attachment in your email.

The manual is 0,65 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kenwood KDC-PS9590R

Kenwood KDC-PS9590R User Manual - German - 56 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info