606320
44
Zoom out
Zoom in
Previous page
1/52
Next page
English
— 44 —— 44 —
What might seem to be a malfunction in your unit may
just be the result of slight misoperation or miswiring.
Before calling service, first check the following table
for possible problems.
General
? The power does not turn ON.01
The fuse has blown.
After checking for short circuits in the wires, replace the fuse with
one with the same rating.
No ACC position on vehicle ignition.02
Connect the same wire to the ignition as the battery wire.
? If you have selected Standby mode, the power will go OFF
automatically.03
The Power OFF Timer function has been activated.
If you do not want the power to go OFF automatically, cancel the
Power OFF Timer function.
? Nothing happens when the buttons are pressed.04
The computer chip in the unit is not functioning normally.
Press the reset button on the unit (page 4).
? There’s a source you can’t switch.06
There’s no CD inserted.
Set the media you want to listen to. If there’s no media in this
unit, you can't switch to each source.
? The faceplate does not open or close.09
The faceplate is incorrectly attached.
Reattach the faceplate correctly, See the section on <Removing
the Faceplate>(page 16).
? The memory is erased when the ignition is turned OFF.10
The battery wire has not been connected to the proper terminal.
Connect the wire correctly, referring to the section on
<Connecting Wires to Terminals>.
The ignition and battery wire are incorrectly connected.11
Connect the wire correctly, referring to the section on
<Connecting Wires to Terminals>.
? There’s no loudness effect.12
You’re using Non-fading preout.
Loudness has no effect in Non-fading preout.
? The TEL mute function does not work.15
The TEL mute wire is not connected properly.
Connect the wire correctly, referring to the section on
<Connecting Wires to Terminals>.
? The TEL mute function turns ON even though the TEL mute wire is
not connected.16
The TEL mute wire is touching a metal part of the car.
Pull the TEL mute wire away from the metal part of the car.
? The Bass center frequency, Bass quality factor, Bass extend, Middle
center frequency, Middle quality factor, and Treble center frequency
can’t be adjusted.19
The <System Q> (page 10) is set OFF.
Set it ON.
? No sound can be heard, or the volume is low.
The fader or balance settings are set all the way to one side.21
Center the fader and balance settings.
The input/output wires or wiring harness are connected incorrectly.22
Reconnect the input/output wires or the wiring harness correctly.
See the section on <Connecting Wires to Terminals>.
The values of Volume offset are low.24
Increase the values of Volume offset. (page 10)
The <Built-in Amp Mute Setting> (page 33) is ON.100
Turn it OFF.
? The sound quality is poor or distorted.25
One of the speaker wires is being pinched by a screw in the car.
Check the speaker wiring.
The speakers are not wired correctly.27
Reconnect the speaker wires so that each output terminal is
connected to a different speaker.
Troubleshooting Guide
KDC-M907 _U.S 04.2.4 4:17 PM Page 44
44


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kenwood KDC-M907 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood KDC-M907 in the language / languages: English as an attachment in your email.

The manual is 1,05 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kenwood KDC-M907

Kenwood KDC-M907 User Manual - German - 50 pages

Kenwood KDC-M907 User Manual - Dutch - 50 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info