36072
6
Zoom out
Zoom in
Previous page
1/10
Next page
1 Cómo remover los tornillos de transporte
Antes de comenzar a instalar la unidad,
saque los 3 tornillos de transporte
empleados para proteger el mecanismo
interno.
Después de quitar el tornillo de transporte,
guárdelo cuidadosamente y vuelva a
utilizarlo antes de transportar de nuevo la
unidad.
2 Conmutadores de ajuste de ángulo
Los conmutadores de ajuste de ángulo
ubicados en ambos lados del aparato
deberán ajustarse según el ángulo de
instalación del cambiador de discos
compactos automático. Ponga ambos
conmutadores en la misma posición. Si
los conmutadores están mal ajustados, el
sonido saltará o podrá producirse un mal
funcionamiento.
Efectúe el reglaje de los interruptores de
ajuste de ángulo con una moneda u otro
objeto plano.
Cambiar el interruptor gradualmente
quitando y usando de nuevo el objeto al
final de cada paso.
3 Tape los agujeros indicados por la 3 con
sellos guardapolvos E. (Fondo y costados).
Utilice los agujeros marcados para
instalar la unidad.
No apriete firmemente el tornillo B en el
momento de realizar la instalación; apriételo
firmemente después de haber fijado el
soporte A.
1 Retirando os parafusos de transporte
Retire todos os três parafusos de
transporte de proteção do mecanismo
interno antes de iniciar a instalação do
aparelho.
Depois de retirar o parafuso de transporte,
guarde-o com cuidado e coloque-o de novo
antes de transportar a unidade.
2 Comutadores de ajuste de ângulo
Os interruptores de ajuste do ângulo em
ambos os lados da unidade devem ser
ajustados de acordo com o ângulo de
instalaçào do cambiador de CD
automático. Ajuste ambos interruptores
para a mesma posição. Se os
interruptores não forem ajustados
adequadamente, pode ocorrer salto do
som ou outras falhas.
Acerte os interruptores de ajuste de
ângulo com uma moeda ou outro objeto
chato.
Mude o interruptor passo a passo,
desprendendo e utilizando novamente o
objecto ao fim de cada passo.
3 Cubra os furos indicados por 3 com os
selos à prova de poeira E.(Embaixo e nos
lados)
Use os furos marcados para instalar o
aparelho.
Não apertar o parafuso B demasiadamente
ao instalá-lo, mas apertá-lo firmemente
depois de fixado o suporte A.
2CUIDADO
NOTA
2PRECAUCIÓN
NOTA
Angle adjustment switches /
Commutateurs de réglage d’angle /
Conmutadores de ajuste de ángulo /
Comutadores de ajuste de ângulo
It is not possible to install at an angle of 40°~50° if only A is used. /
L’installation à une inclinaison de 40°~50° est impossible en utilisant A. /
No es posible realizar una instalación con un ángulo de 40°~50° si sólo se utiliza A. /
Não é possível instalar num ângulo de 40° ~ 50° se for usado apenas A. /
90
0
45
Installation angle /
Angle d’installation /
Angulo de instalación /
Ângulo de instalação
Angle adjustment switch position /
Position des commutateurs de réglage d’angle /
Posición de los conmutadores de ajuste de
ángulo /
Posição do comutador de ajuste de ângulo
85°~90°40°~50°0°~5°
9090
0
45
90
0
45
L
R
Accessories / Accessoires / Accesorios / Acessórios
A × 2 B × 4 C × 4 D × 1 E × 1 F × 1
Installation Procedure / Procédure d’installation /
Procedimiento de instalación / Procedimentos para Instalação
1
Removing the transportation screws
Remove all 3 transportation screws for
protecting the internal mechanism before
you start to install the unit.
After removing the transport screw, retain
it carefully and attach it again before
transporting the unit again.
2 Angle adjustment switches
The angle adjustment switches on the
both side of the unit are to be set
according to the angle of installation of
the CD auto changer. Set both of the two
switches to the same position. If the
switches are not set properly, sound skip
or other malfunction may occur.
Set the angle adjustment switches with a
coin or other flat object.
Change the switch step by step by
detaching and reusing the obdect at the
end of each step.
3 Cover the holes indicated by 3 with the
dustproof seals E. (Bottom and sides)
Use the holes marked to install the unit.
Do not tighten the screw B too securely at
the time of installation, but tighten it
securely after having fixed the bracket A.
1 Comment enlever les vis de transport
Retirez les 3 vis de transport pour la
protection du mécanisme interne avant de
commencer l'installation.
Après avoir retiré la vis de transport,
rangez-la avec soin et n'omettez pas de la
poser à nouveau avant de transporter
l'appareil.
2 Commutateur de réglage d’angle
Les commutateurs de réglage d’angle qui
se trouvent de chaque coté de l’appareil
doivent être placés dans la position
correspondant à l’angle d’installation du
changeur de CD. Les deux commutateurs
doivent être dans la même position. SI
ces commutateurs ne sont pas
convenablement réglés, il peut y avpir des
ratées de son ou d’autres problèmes de
fonctionnement.
Réglez les commutateurs d'angle
d'ajustement avec une pièce de monnaie
ou un autre objet plat.
Changer le commutateur pas à pas en
détachant et un utilisant à nouveau l’objet
à la fin de chaque opération.
3 Couvrez les trous indiqués par 3 avec les
joints anti-poussière E. (Partie inférieure et
côtés)
Utilisez les trous marqués pour installer
l'appareil.
Lors de l’installation, ne serrer
complètement la vis B qu’après avoir
monté le support A.
2ATTENTION
REMARQUE
2CAUTION
NOTE
Transportation screws /
Vis de transport /
Tornillos de transporte /
Parafusos de transporte
AUX
OFF ON
'
11
Installation / Installation / Instalación / Instalação
10
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kenwood KDC-CPS81 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood KDC-CPS81 in the language / languages: English as an attachment in your email.

The manual is 0,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kenwood KDC-CPS81

Kenwood KDC-CPS81 User Manual - German, Dutch, Italian - 10 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info