36072
2
Zoom out
Zoom in
Previous page
1/10
Next page
Warning Safety precautions
2 3
The marking of products using lasers
(Except for some areas)
The label is attached to the chassis/case and
says that the component uses laser beams that
have been classified as Class 1. It means that
the unit is using laser beams that are of a
weaker class. There is no danger of hazardous
radiation outside the unit.
Marquage des produits utilisant un
laser (Sauf pour certaines régions)
L’étiquette est attachée au chassis/boîtier de
l’appareil et indique que l’appareil utiliser des
rayons laser de classe 1. Cela signifie que
l’appareil utilise des rayons laser d’une classe
faible. Il n’y a pas de danger de radiation
accidentelle hors de l’appareil.
La marca del producto láser
Esta etiqueta está colocada al chasis/a la caja e
indica que el componente funciona con rayos
láser de classe1.
Esto significa que el aparato utiliza rayos láser
considerados como de clase débie. No existe
el peligro de que este aparato emita al exterior
una radiación peligrosa.
A marca dos produtos usando laser
(exceto para algumas áreas)
A etiqueta é presa no chassis/estojo e indica
que o componente utiliza raios laser,
classificados como sendo de Classe 1. Isto
significa que o aparelho está usando raios laser
que são de uma classe mais fraca. Não há
perigo de radiação maléfica fora do aparelho.
Use of controls or adjustments or performance
of procedures other than those specified herein
may result in hazardous radiation exposure.
In compliance with Federal Regulations,
following are reproductions of labels on, or
inside the product relating to laser product
safety.
Location : Rear Panel
FCC WARNING
This equipment may generate or use radio
frequency energy. Changes or modifications to
this equipment may cause harmful interference
unless the modifications are expressly approved
in the instruction manual. The user could lose
the authority to operate this equipment if an
unauthorized change or modification is made.
This equipment has been tested and found to
comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference in a
residential installation. This equipment may
cause harmful interference to radio
communications, if it is not installed and used in
accordance with the instructions. However,
there is no guarantee that interference will not
occur in a particular installation. If this
equipment does cause harmful interference to
radio or television reception, which can be
determined by turning the equipment off and on,
the user is encouraged to try to correct the
interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the
equipment and receiver.
Connect the equipment into an outlet on a
circuit different from that to which the receiver
is connected.
Consult the dealer or an experienced radio/TV
technician for help.
This Class B digital apparatus meets all
requirements of the Canadian interference-
Causing Equipment Regulations.
Cet appareil numérique de la classe B respecte
toutes les exigences du Reglement sur le
matériel brouilleur du Canada.
REMARQUE
NOTE
NOTE
2CAUTION
CLASS 1
LASER PRODUCT
CLASS 1
LASER PRODUCT
CLASS 1
LASER PRODUCT
CLASS 1
LASER PRODUCT
KENWOOD CORPORATION
2967-3, ISHIKAWA-CHO,
HACHIOJI-SHI
TOKYO, JAPAN
KENWOOD CORP. CERTIFIES THIS EQUIPMENT
CONFORMS TO DHHS REGULATIONS N0.21 CFR
1040. 10, CHAPTER I, SUBCHAPTER J.
Take the following precautions to prevent fire
and avoid personal injury :
Check that no metal objects (coins, tools,
etc.) are left inside the unit to avoid short
circuits.
If you smell or see smoke, turn the power off
immediately and consult your Kenwood
dealer.
Take the following precautions to keep the
unit in proper working order.
Do not open the top or bottom cover.
Do not install the unit in places it is exposed
to direct sunlight, high heat or humidity,
water may splash over it, or dust exists.
Do not install the unit at a dusty place. If the
unit is installed at a dusty place, dust
accumulates inside the unit and unit may be
damaged.
When drilling a hole in the car to fix the
brackets, make sure not to damage the fuel
tank, brake tube, wiring harnesses, etc. on
the other side.
If the unit is installed near speakers, the
speakers vibration may causes a sound skip.
Install the unit as far away as possible from
the speakers.
If you have difficulty in installing this unit in
your vehicle, contact your Kenwood dealer.
If it doesn't seem to be working properly,
first press the Reset button. If the
malfunction persists, consult your Kenwood
dealer.
IMPORTANT INFORMATION
This unit is NOT designed to be connected
directly to control units that are manufactured
and sold before 1994. If used with such units,
an optional CA-SD200 (sold separately) must
be used.
FAILURE TO FOLLOW THESE
INSTRUCTIONS MAY RESULT IN DAMAGE
TO THIS UNIT AND CONTROL UNIT.
The disc name preset function can register
names of up to 100 discs using up to 12
characters for each disc name.
The availability of this function as well as the
number of discs which can be registered
using this function and the number of usable
characters may be variable depending on the
control unit in use.
Do Not Use Special Shape CDs
Be sure to use round shape CDs only for this
unit and do not use any special shape CDs.
Use of special shape CDs may cause the unit
to malfunction.
Be sure to use CDs with disc mark
only for this unit.
Cleaning the unit
If the front panel is dirty, wipe it clean with a
silicon cloth or soft dry cloth with the power
off.
Do not use hard cloths or paint thinner,
alcohol, or other volatile solvents. These may
damage external surfaces or remove indicator
characters.
Lens fogging
In cold climates, there may be a period after
you turn on your vehicle's heater when the
lens that guides the laser beam used in your
CD player fogs up. If this happens, you
cannot play compact discs. Take out discs
and the fogging will disappear. If it does not
return to normal after several hours, contact
your Kenwood dealer.
Heat protection
In warm climates, when vehicles are left
standing in direct sunlight with the windows
closed, the temperature inside can rise above
60°C. The unit's protection circuits will then
display the message "HOLD" and prevent the
player from operating. Just open the
windows or turn on the air conditioning. As
soon as the "HOLD" message disappears, the
player will operate normally.
2CAUTION
NOTE
2CAUTION
2WARNING
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kenwood KDC-CPS81 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood KDC-CPS81 in the language / languages: English as an attachment in your email.

The manual is 0,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kenwood KDC-CPS81

Kenwood KDC-CPS81 User Manual - German, Dutch, Italian - 10 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info