511172
79
Zoom out
Zoom in
Previous page
1/82
Next page
English
|
79
17-3. Error messages
The messages shown below indicates your system
condition.
ö "TOC Error"
Í The CD is quite dirty. The CD is upside-down. The CD
is scratched a lot.
Í The disc is unreadable.
ö "IN" (blink)
Í The CD player section is not operating properly.
ò Reinsert the CD. If the CD cannot be ejected or
the display continues to blink even when the CD
has been properly reinserted, please switch off the
power and consult your nearest service center.
ö "Protect" (blink)
Í The speaker wire has short-circuited or touched
the chassis of the vehicle, and then the protection
function has been activated.
ò Lay or insulate the speaker cable properly and
press the Reset button. If "Protect" does not
disappear, consult your nearest service center.
ö "NA File"
Í An Audio file is played in a format that is not
supported by this unit.
ö "Copy PRO"
Í A copy-protected file is played.
ö "Read Error"
Í The file system of the connected USB device is
broken.
ò Copy the files and folders for the USB device
again. If "Read Error" is still displayed, initialize the
USB device or use another USB device.
ö "No Device"
Í A USB device is selected as a source although no USB
device is connected.
ò Change the source to any source other than the
USB device. Connect a USB device, and change
the source to the USB device again.
ö "N/A Device"
Í An unsupported USB device is connected.
Í Connection to the iPod has failed.
ò Check that the connected iPod is supported.
See <8-6. About the Audio file> (page 39) for
information on supported iPods.
ö "No Music Data"
Í The connected USB device contains no playable
audio file.
Í A medium that does not have playable data has been
played.
ö "Please Eject"
Í The unit is malfunctioning for some reason.
ò Press and hold [G].
ò Press the reset button on the unit. If the "Please
Eject" code does not disappear, consult your
nearest service center.
ö "iPod Error"
Í Connection to the iPod has failed.
ò Remove the iPod and then reconnect it.
ò Reset iPod/ iPhone.
ö "No Number"
Í The calling party does not notify a caller ID.
Í There is no phone number data.
ö "No Data"
Í There is no outgoing call list.
Í There is no incoming call list.
Í There is no missed call list.
Í There is no phone book list.
ö "No Entry"
Í The cell phone has not been registered (pairing).
ö "HF Disconnect"
Í The unit cannot communicate with the cell phone.
ö "AUD Disconnect"
Í The unit cannot communicate with the Bluetooth
audio player.
ö "HF Error 68"
Í The unit cannot communicate with the cell phone.
ò Cycle the power switch. If this message still
appears, press the Reset button on the control
unit.
ö "HF Error 89"
Í Update of the firmware has failed.
ò Retry update of the firmware.
ö "Device Full"
Í 5 Bluetooth device have already been registered. No
more Bluetooth devices are registered.
ö "Pairing Failed"
Í Pairing error.
ö "N/A Voice Tag"
Í No voice tags are registered in your cell phone.
ö "No Phonebook"
Í Data is not contained in the phone book.
ö "No Support"
Í The connected Bluetooth device does not support a
voice recognition function.
ö "No Active Device"
Í Any Bluetooth device supporting a voice recognition
function is not connected.
ö "Antenna Error"
Í The antenna has a short-circuit and the protective
circuit has activated.
ò Check the Digital Radio antenna. If a passive
antenna without a booster is used, set "DAB
Antenna Power" to "OFF". Refer to <10-10. Digital
Radio initial settings> (page 51)
79


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kenwood KDC-BT73DAB at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood KDC-BT73DAB in the language / languages: English as an attachment in your email.

The manual is 0,57 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kenwood KDC-BT73DAB

Kenwood KDC-BT73DAB Quick start guide - English, German - 152 pages

Kenwood KDC-BT73DAB User Manual - German - 82 pages

Kenwood KDC-BT73DAB Quick start guide - German - 20 pages

Kenwood KDC-BT73DAB Quick start guide - Dutch - 152 pages

Kenwood KDC-BT73DAB User Manual - Dutch - 82 pages

Kenwood KDC-BT73DAB Quick start guide - Dutch - 20 pages

Kenwood KDC-BT73DAB Quick start guide - French, Italian, Portuguese, Spanish - 152 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info