Manual Kenwood KDC-BT6544U (page 39 of 48) (English, Dutch)

66349

Zoom out

Zoom in

1/48

English

Accessories/ Installation Procedure

Accessories

..........1

..........2

Installation Procedure

1. To prevent short circuits, remove the key from the

ignition and disconnect the - terminal of the

battery.

2. Make the proper input and output wire

connections for each unit.

3. Connect the wire on the wiring harness.

4. Take Connector B on the wiring harness and

connect it to the speaker connector in your vehicle.

5. Take Connector A on the wiring harness and

connect it to the external power connector on your

vehicle.

6. Connect the wiring harness connector to the unit.

7. Install the unit in your car.

8. Reconnect the - terminal of the battery.

9. Press the reset button.

• Mounting and wiring this product requires skills and

experience. For safety’s sake, leave the mounting and wiring

work to professionals.

• Make sure to ground the unit to a negative 12V DC power

supply.

• Do not install the unit in a spot exposed to direct sunlight

or excessive heat or humidity. Also avoid places with too

much dust or the possibility of water splashing.

• Do not use your own screws. Use only the screws provided.

If you use the wrong screws, you could damage the unit.

• If the power is not turned ON (“PROTECT” is displayed),

the speaker wire may have a short-circuit or touched the

chassis of the vehicle and the protection function may

have been activated. Therefore, the speaker wire should be

checked.

• Make sure that all wire connections are securely made by

inserting jacks until they lock completely.

• If your vehicle’s ignition does not have an ACC position, or

if the ignition wire is connected to a power source with

constant voltage such as a battery wire, the power will not

be linked with the ignition (i.e., it will not turn on and off

along with the ignition). If you want to link the unit’s power

with the ignition, connect the ignition wire to a power

source that can be turned on and off with the ignition key.

• Use a commercially available conversion connector if the

connector does not fit in the vehicle connector.

• Insulate unconnected wires with vinyl tape or other similar

material. To prevent a short circuit, do not remove the caps

on the ends of the unconnected wires or the terminals.

• If the console has a lid, make sure to install the unit so that

the faceplate will not hit the lid when closing and opening.

• If the fuse blows, first make sure the wires aren’t touching

to cause a short circuit, then replace the old fuse with one

with the same rating.

• Connect the speaker wires correctly to the terminals to

which they correspond. The unit may be damaged or fail to

work if you share the - wires or ground them to any metal

part in the car.

• After the unit is installed, check whether the brake lamps,

blinkers, wipers, etc. on the car are working properly.

• Mount the unit so that the mounting angle is 30° or less.

• Reception may drop if there are metal objects near the

Bluetooth antenna.

Bluetooth antenna unit

For Good Reception

To assure good reception, note the following:

• Communicate with the cell-phone within the line-

of-sight distance of 10 m (30 ft). The communication

range becomes shorter depending on the

surrounding environment. The communication

range also becomes shorter when there is an

obstacle between this unit and the cell-phone. The

above maximum communication range (10 m) is

not always assured.

• A broadcast station or walkie-talkie located nearby

can interfere with communication due to too strong

signal.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood KDC-BT6544U in the language / languages: English, Dutch as an attachment in your email.

The manual is 1,16 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kenwood KDC-BT6544U

Kenwood KDC-BT6544U User Manual - Dutch - 48 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Kenwood KDC-BT6544U Manual

Product: