633366
14
Zoom out
Zoom in
Previous page
1/16
Next page
14
KAF-3010R/1010 (En)
In case of difficulty
NoteNote
Note
Do not use contact cleaners because it could cause a malfunction. Be specially careful against contact cleaners containing oil, for
they may deform the plastic components.
Operation to reset
The microcomputer may fall into malfunction (impossibility to
operate, erroneous display, etc.) when the power cord is un-
plugged while power is ON or due to an external factor. In this
case, execute the following procedure to reset the microcom-
puter and return it to normal condition.
Set the POWER to OFF then, while holding down the SOURCE
DIRECT key, set the POWER switch to ON.
Symptom
Remote control unit (KAF-3010R only)
Cause Remedy
Batteries are exhausted.
The remote control unit is too far away
from the main system, controlling angle is
too large, or there is an obstacle in be-
tween.
The audio cords and system control cords
are not connected properly.
The source component to be operated
does not contain the tape(s) or CD.
The POWER switch is set to OFF.
Remote control operation is not possible
Replace with new batteries. 9
Operate the remote control unit within the
controllable range.
9
Connect properly referring to “System
connection”.
45
Place the tape(s) or CD in the source com-
ponent to be played.
Set the POWER switch to ON. 0
Speaker protection circuit
When this unit’s power is turned ON with the speaker cable short-circuited, the speaker protection functions.
If the standby indicator blinks (KAF-3010R) or the MUTING indicator blinks (KAF-1010) and no sound occurs, turn the power
OFF, remove the short-circuit, then turn the power ON again.
Please note that resetting the microcomputer clears the contents
stored in it and returns it to the condition when it left the factory.
The speaker cords are disconnected.
The VOLUME CONTROL is set to the
minimum position.
MUTING is ON.
(The MUTING indicator is blinking)
The SPEAKERS switches are set to OFF.
The system control cords are not fully con-
nected.
Speaker cords are short-circuited.
The speaker cord is disconnected.
The BALANCE control is set to an extreme
position.
Symptom
Cause Remedy
Connect them properly referring to “Sys-
tem connection”.
6
Adjust the volume to a proper level.0
Press the MUTING key to OFF. !
Set the SPEAKERS switch(es) to ON.
0
Check the system control connections.
45
Turn the power off, eliminate the short-cir-
cuiting, then turn on the power again.
Connect it properly referring to “System
connection”.
6
Adjust the Left/Right balance. !
Sound is not output.
The standby indicator blinks and sound
is not output. (KAF-3010R)
The MUTING indicator blinks and sound
is not output. (KAF-1010)
Sound is not output from one of the
speakers.
Amplifier
What appears to be a malfunction may not always be serious. If your unit should not perform as expected, consult the table below
to see if the problem can be corrected before seeking help from your dealer or service representative.
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kenwood KAF-1010 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood KAF-1010 in the language / languages: English as an attachment in your email.

The manual is 0,5 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info