159078
19
Zoom out
Zoom in
Previous page
1/20
Next page
19
EN
ENGLISH
In case of difficulty
Resetting the Microcomputer
The microcomputer may malfunction (unit can-
not be operated, or shows an erroneous dis-
play) if the power cord is unplugged while the
power is ON, or due to some other external
factor. If this happens, execute the following
procedure to reset the microcomputer and re-
turn the unit to its normal operating condition.
Plug in the AC power cord to the wall out-
let, and within 5 seconds, press and hold
down the 7 button and press CD button.
Please note that resetting the microcomputer
will clear the contents of the memory and
return the unit to the state it was in when it
left the factory.
Check that following guide for problem resolution.
General
No sound.
\ Plug in AC cord securely.
\ Set the VOLUME control to proper
sound level.
\ Make sure the source is set to the
source you wish to operate.
\ Pull out the headphones plug from the
headphones jack.
The left and right sound outputs are reverse.
\ Check the speaker connections and
location.
The system displays features automatically.
\ Switch off the demo operation.
CD player operation
“NO DISC” is displayed.
\ Insert a disc correctly (label side up).
\ Clean the disc.
\ Use a new or readable disc.
\ Wait until the moisture condensation
at the lens has cleared.
\ Plug in AC cord securely.
Radio reception
Noise in radio.
\ Tune to a correct frequency.
\ Adjust the direction of the FM antenna.
\ AM antenna is built in; rotate the sys-
tem to face a new direction.
\ Increase the distance between the sys-
tem and TV or VCR.
Cassette deck operation
Cannot record.
\ Replace the tape or cover tabs with
adhesive tape.
\ Clean the head.
\ Use only NORMAL (IEC I) tape.
\ Do not use a cassette with more than
90-minute recording time, for the tape
used in such a cassette is very thin and
tends to cause problem such as en-
tanglement around the pinch roller or
could be easily cut off.
Timer / Clock
The timer is not working.
\ Set the correct clock.
\ Press the TIMER ON/OFF button to
switch on the timer.
\ Switch the system to standby mode.
The timer/clock is erased.
\ Power has been interrupted or power
cord has been disconnected. Set it
again.
Remote control
Does not function properly.
\ Replace the batteries.
\ Remove the obstacles.
\ Move closer to the system when us-
ing the remote control and make sure
that you are pointing at unit’s remote
sensor.
5521_08_20_EN 04.6.30, 3:22 PM19
19


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kenwood hm 437 mp at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood hm 437 mp in the language / languages: English as an attachment in your email.

The manual is 0,35 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kenwood hm 437 mp

Kenwood hm 437 mp User Manual - German, Dutch, French, Italian, Spanish - 100 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info