Manual Kenwood ES020 series (page 4 of 87) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

510774

Zoom out

Zoom in

1/87

before using for the first time

1 Read these instructions carefully and retain for future reference.

2 Remove all packaging and any labels.

3 Wash the parts: see ‘cleaning’.

4 Flush the machine through with clean water: see ‘before making coffee for the

first time’.

safety

● Never remove the filter holder whilst coffee is brewing or steam is being

produced - steam could shoot out and burn you.

● Don’t get burnt by:

●●

hot parts, including the steam nozzle, filter holder and coffee outlet.

●●

steam coming out of the steam nozzle or coffee from the coffee outlet.

● Keep children away from the machine. And never let the cord hang down

where a child could grab it.

● Never use a damaged machine. Get it checked or repaired: see ‘service and

customer care’.

● Never put the machine in water or let the cord or plug get wet - you could get

an electric shock.

● Unplug:

●●

before filling with water

●●

before cleaning

●●

after use.

● Never leave the machine on unattended.

● Don’t let the cord touch hot parts.

●

This appliance is not intended for use by persons (including children) with

reduced physical, sensory or mental capabilities, or lack of experience and

knowledge, unless they have been given supervision or instruction concerning

use of the appliance by a person responsible for their safety.

●

Children should be supervised to ensure that they do not play with the

appliance.

●

Only use the appliance for its intended domestic use. Kenwood will not accept

any liability if the appliance is subject to improper use, or failure to comply with

these instructions.

important

● Never use without water - the pump will burn out.

● Keep the machine above 0°C - otherwise any water in the machine will freeze

and cause damage.

● Never use without the drip tray and cup stand.

before plugging in

● Make sure your electricity supply is the same as the one shown on the

underside of your machine.

●

This appliance conforms to EC directive 2004/108/EC on Electromagnetic

Compatibility and EC regulation no. 1935/2004 of 27/10/2004 on materials

intended for contact with food.

know your Kenwood espresso machine

ቢ removable water tank

ባ lid

ቤ finger grip for steam nozzle

ብ steam tube

ቦ steam nozzle

ቧ coffee outlet

ቨ variable steam knob

ቩ small filter for 1 cup dispensing or coffee pod

ቪ tab

ቫ large filter for 2 cup dispensing only

ቭ coffee button

ቮ coffee ready indicator light

ቯ on/off button

ተ steam ready indicator light

ቱ steam button

ቲ drip tray

ታ float

ቴ cup stand

ት measuring spoon/coffee tamper

ቶ filter holder

filter emptying lever

cup storage tray

before making coffee for the first time

1 Make sure the variable steam knob is closed by turning clockwise (don’t

overtighten).

2 Lift the lid, then lift out the tank and fill with cold water. Never fill above the

“MAX” level marked. Alternatively lift the lid and fill the tank whilst in position.

● We recommend using filtered water as it produces better coffee and reduces

limescale. Never use fizzy water or any other liquid.

3 Re fit the tank. Make sure that it is correctly located and apply light pressure if

necessary to ensure the valve at the bottom of the tank connects with the

bottom of the machine.

Important

Never operate the machine without water in the tank. Top up as

soon as the level gets low.

4 Close the lid.

5 Hold the finger grip and swing out the steam nozzle and put a jug underneath.

6 Attach the filter holder to the machine by positioning it under the coffee outlet

and turning to the right ᕡ. Place a suitably sized container underneath.

7 Connect to the power supply then press the on/off button and it will glow

orange. At the same time the green coffee ready indicator light will flash. Wait

until the green light stops flashing.

8 Open the variable steam knob by turning anti-clockwise and press the coffee

button and allow one cup of water to flow out of the steam nozzle. Close the

variable steam knob and allow one cup of water to flow out of the coffee outlet

into the container.

9 Press the coffee button to stop the flow, then press the on/off button to switch

off the machine.

10 Repeat these steps if you haven’t used the coffee maker for a few days.

preheating the coffee machine

To ensure your espresso coffee is dispensed at the right temperature it is

necessary to pre-heat the coffee unit.

1 Check that the variable steam knob is firmly closed (turn clockwise) and that

there is sufficient water to heat 1 or 2 cups as required.

2 Fit the desired filter into the filter holder (without coffee and making sure that the

tab on the filter fits into the slot on the filter holder). Attach to the machine by

positioning it under the coffee outlet and turning to the right ᕡ. Ensure it is

firmly located.

3 Position a cup under the filter holder. Using the same cup that the coffee will be

served in will ensure it is preheated.

4 Press the on/off button and it will glow orange. At the same time the green

coffee ready indicator light will flash. Wait until the green light stops flashing.

5 Press the coffee button and it will glow orange, and hot water will dispense into

the cup. When the green coffee ready light starts flashing again, press the

coffee button to stop the flow.

6 Remove the filter holder and proceed to make coffee using either ground coffee

or coffee pods.

to make espresso using ground coffee

1 Pre heat the appliance as described on page 2.

2 Check that there is water in the tank.

3 Select the desired filter.

● Use the smaller filter for making one cup of coffee (or when using coffee pods)

and the larger filter for 2 cups.

4 Add the coffee using the measuring spoon provided one level spoon per cup,

level the surface then lightly press with the coffee tamper. Wipe off any coffee

around the rim.

● When buying ground coffee make sure it is suitable for espresso machines.

● Never press the coffee too firmly as it will block the filter and the coffee will

come out very slowly and the crema will be of a dark colour. However, if it is

pressed too lightly, the coffee will come out too fast and the crema will be a

light colour and the coffee will taste watery.

5 Fit the filter holder. Make sure that the tab on the filter fits into the slot on the

filter holder.

6 Fit the filter holder into the coffee outlet. Turn it to the right to lock into position

ᕡ.

● Put one or two cups underneath ᕢ. If making one cup of coffee, centre your

cup in the middle.

7 Press the on/off button and wait until the green coffee ready indicator light

stops flashing, then press the coffee button.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood ES020 series in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,38 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Kenwood ES020 series Manual

Product: