672783
42
Zoom out
Zoom in
Previous page
1/48
Next page
42
The license and distribution terms for any
publically available version or derivative of
this code cannot be changed. i.e. this code
cannot simply be copied and put under
another distribution license [including the
GNU Public License.]
--------------------------------------------------------
CRC utility
COPYRIGHT (C) 1986 Gary S. Brown. You
may use this program, or code or tables
extracted from it, as desired without
restriction.
First, the polynomial itself and its table of
feedback terms. The polynomial is +X^1
1+X^10+X^8+X^7+X^5+X^4+X^2+X^
1+X^0
Note that we take it "backwards" and put
the highest-order term in the lowest-order
bit. The X^32 term is "implied"; the LSB is
the X^31 term, etc. The X^0 term (usually
shown as "+1") results in the MSB being 1
Note that the usual hardware shift register
implementation, which is what we're
using (we're merely optimizing it by
doing eight-bit chunks at a time) shifts
bits into the lowest-order term. In our
implementation, that means shifting
towards the right. Why do we do it this
way? Because the calculated CRC must be
transmitted in order from highest-order
term to lowest-order term. UARTs transmit
characters in order from LSB to MSB. By
storing the CRC this way we hand it to the
UART in the order low-byte to high-byte;
the UART sends each low-bit to hight-bit;
and the result is transmission bit by bit
from highest- to lowest-order term without
requiring any bit shuing on our part.
Reception works similarly
The feedback terms table consists of 256,
32-bit entries. Notes
The table can be generated at runtime if
desired; code to do so is shown later. It
might not be obvious, but the feedback
terms simply represent the results of eight
shift/xor operations for all combinations of
data and CRC register values
The values must be right-shifted by eight
bits by the "updcrc logic; the shift must
be unsigned (bring in zeroes). On some
hardware you could probably optimize
the shift in assembler by using byte-swap
instructions polynomial $edb88320
CRC32 code derived from work by Gary S.
Brown.
--------------------------------------------------------
About Open Source Software included
in the viewer software
This viewer software includes certain open
source or other software
originating from third parties that is
subject to the GNU General Public
License version 3 (GPLv3) and di erent
copyright licensees, disclaimers and
notices. The source code of software
licensed under GPLv3 and dierent
copyright licenses, disclaimers and notices
are distributed at the website below,
http://www.kenwood.com/gpl
Important notices regarding software
This product uses software components
(licensed software) in accordance with the
software license agreements granted by
third parties. For details, view the support
information for this product at
http://www.kenwood.com/cs/ce/.
DRV-N520W_EN301.indd 42 2017/03/08 14:06
42


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kenwood DRV-N520 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood DRV-N520 in the language / languages: English as an attachment in your email.

The manual is 2,48 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kenwood DRV-N520

Kenwood DRV-N520 User Manual - German, Dutch - 88 pages

Kenwood DRV-N520 User Manual - French, Italian - 88 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info