Manual Kenwood CMOS 300 (page 2 of 100) (English, German, Dutch, French, Italian, Portuguese, Spanish)

536416

Zoom out

Zoom in

1/100

CMOS-300/CMOS-200

above because of the danger of malfunction due to high

temperatures.)

• Before drilling any mounting holes always check behind

where you want to drill the holes. Do not drill into the gas

line, brake line, electrical wiring or other important parts.

• If this unit is installed in the passenger compartment, anchor

it securely so it does not break free while the car is moving,

and cause injury or an accident.

• If this unit is installed under a front seat, make sure it does not

obstruct seat movement. Route all leads and cords carefully

around the sliding mechanism so they do not get caught or

pinched in the mechanism and cause a short circuit.

Care and maintenance

• When the product gets dirty, wipe dry with a silicon cloth or

soft cloth. If it is seriously stained, remove stain with a cloth

moistened with a neutral cleaner and then wipe the cleaner

away. Do not use a hard cloth and/or a volatile substance

such as lacquer thinner or alcohol, scratches, deformation,

degradation and/or damage may result.

• When a lens component gets dirty, wipe gently with a soft

clock moistened with water. Do not rub with a dry cloth to

prevent scratching the lens.

Installation Procedure

To prevent a short circuit, remove the key from the

ignition and disconnect the - battery.

2 Make the proper input and output wire connections

for each unit.

3 Connect the wiring harness wires in the following

order: ground, ignition, reverse and camera unit.

4 Connect the wiring harness connector to the power

supply box unit.

5 Install the unit in your car.

6 Reconnect the - battery.

2WARNING

• If you connect the ignition wire (Red) to the car chassis

(Ground), you may cause a short circuit, that in turn may

start a ﬁ re. Always connect those wires to the power source

running through the fuse box.

• Do not cut out the fuse from the ignition wire (Red). The

power supply must be connected to the wires via the fuse.

2CAUTION

• If your car’s ignition does not have an ACC position, connect

the ignition wires to a power source that can be turned on

and oﬀ with the ignition key. If you connect the ignition wire

to a power source with a constant voltage supply, as with

battery wires, the battery may die.

• If the fuse blows, ﬁ rst make sure the wires aren’t touching to

cause a short circuit, then replace the old fuse with one with

the same rating.

2WARNING

To prevent injury or fire, take the following

precautions:

• To prevent a short circuit, never put or leave any metallic

objects (such as coins or metal tools) inside the unit.

• Installation and wiring of this product require specialist

skill and experience. To assure your safety, please request a

specialist technician to install the unit.

2CAUTION

To prevent damage to the product, take the

following precautions:

• Make sure to ground the unit to a negative 12V DC power

supply.

• When replacing a fuse, only use a new fuse with the

prescribed rating. Using a fuse with the wrong rating may

cause your unit to malfunction.

• Do not use your own screws. Use only the screws provided. If

you use the wrong screws, you could damage the unit.

NOTE

• This product is a rear view camera for checking the view at

the rear of a car.

• A rear view camera is a camera that provides symmetrical

images in the same way as rear and side view mirrors.

• Connection to a TV with an RCA video input is possible,

but conﬁ rm whether the TV you use has a reverse gear

connection function.

• This product is designed to supplement the driver’s rear

view, but the camera images do not show all dangers and

obstacles. Be sure to look behind you when reversing to

conﬁ rm the view.

• This product features a wide-angle lens, so the near view

is wide and the far view is narrow, which may create a false

sense of distance. Be sure to look behind you when reversing

to conﬁ rm the view.

• Do not wash your car with an automatic car wash or high-

pressure water as it may result in water entering the camera

or the camera falling oﬀ .

• Check camera bracket installation before driving.

Are the screws loose?

- Is the camera bracket ﬁ rmly secured?

- If the rear view camera comes loose while you are driving it

may cause an accident.

• Before ﬁ nally installing the unit, connect the wiring

temporarily, making sure it is all connected up properly, and

the unit and the system work.

• When mounting this unit, make sure none of the leads are

trapped between this unit and the surrounding metalwork or

ﬁ t t i n g s .

• Do not mount this unit near the heater outlet, where it would

be aﬀ ected by heat, or near the doors, where rainwater

might splash onto it. (Never install in locations such as the

Before Use/ Installation Procedure

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood CMOS 300 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 3,78 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Kenwood CMOS 300 Manual

Product: