565392
5
Zoom out
Zoom in
Previous page
1/60
Next page
CMOS-320/CMOS-220
|
5
ENGLISH
Installing the Camera/Adjusting its
angle
1 Decide the camera installation position.
2 Clean the camera installation surface.
Using a commercially available cleaner, wipe dirt, moisture
and oil away from the surface on which the camera bracket
is to be attached.
3 Loosen the camera bracket retaining screws.
Using a commercially available
Phillips screwdriver, loosen the
two retaining screws.
Perform steps 4 and 5 only when they are required.
4 If required, separate the camera bracket from
the camera and adjust the shape according to
the surface on which it will be attached.
Bend
Bend
Camera bracket
Adjust the camera bracket
shape so that it fits the
camera installation
position.
5 Mount the camera on the camera bracket.
Mount so that the “KENWOOD” logo appears at the top.
6 Fix the camera temporarily with tape, etc.
Using a piece of tape, etc., fix the camera temporarily.
12345
Install the camera at the center of the vehicle and not to
hide the number plate. And also install straight toward the
forward/reverse direction of the vehicle. Be careful not to
lean the camera toward other directions of the vehicle, etc.
7 Complete all of the required connections.
8 Display the camera video.
Before viewing the camera, apply the parking brake
and chock the wheels so that the vehicle will not move.
Otherwise, an unexpected accident may result.
For displaying the camera video, read the instruction manual
for your video monitor.
When the camera is installed as a rearview
camera:
Change the shift lever to the R (Reverse) range
to view the image of the rear of the vehicle.
When the camera is installed as a front camera
(CMOS-320 only):
Refer to the instruction manual of the unit that
you have connected this camera to, and display
the image of the front of the vehicle.
9 Adjust the camera angle.
When adjusting the camera angle, be careful not to stretch
the camera cord.
When installing CMOS-220 as a rearview
camera:
Adjust the angle so that the rear of the vehicle or the bumper
can be seen at the bottom of the monitor.
Vehicle rear part or bumper
When installing CMOS-320 as a rearview
camera:
Refer to “Display View Switching” (page 14) and switch the
image to [Overhead View]. Adjust the camera angle so that
the guideline and the parking lines become vertical.
Guideline
Installation
When installing CMOS-320 as a front camera:
Before adjusting the camera angle, perform “Camera ID
Setting” (page 13) and “Camera Setting Procedure” (page
10).
When you select [Standard] for “Mounting Position Setting”,
switch the image to [Overhead View] (page 14) and adjust
the camera angle so that the guideline and the parking lines
become vertical.
When you select [Lower] for “Mounting Position Setting”,
switch the image to [Corner View] (page 14) and then adjust
the angle of the camera to straighten the ground lines in the
left and right screens.
10 Set the camera.
When using CMOS-320 as a rearview camera:
Refer to page 9 to 13 and perform “Preparation Before
Camera Setting, “Overhead View Image Adjustment” and
“Wide View Guideline Adjustment”.
When using CMOS-320 as a front camera:
When you select [Standard] for “Mounting Position Setting”,
refer to page 9 to 13 and perform “Preparation Before Camera
Setting, “Overhead View Image Adjustment” and “Wide
View Guideline Adjustment.
When you select [Lower] for “Mounting Position Setting”,
refer to page 9 to 13 and perform “Preparation Before Camera
Setting” and “Overhead View Image Adjustment. You cannot
perform “Wide View Guideline Adjustment”.
11 After adjusting the camera angle, tighten the
retaining screws firmly.
Inspect the retaining screws at times. If they are loose,
tighten them firmly.
Next page 3
LVT2720-001A.indb 5 14/02/14 15:10
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kenwood CMOS-220 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood CMOS-220 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 3,62 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kenwood CMOS-220

Kenwood CMOS-220 User Manual - English - 15 pages

Kenwood CMOS-220 User Manual - German - 15 pages

Kenwood CMOS-220 User Manual - Dutch - 15 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info