517399
9
Zoom out
Zoom in
Previous page
1/16
Next page
IINSTALLATION
MOTOR PULLEY ADJUSTMENT (Figure 13)
NOTE: ALL DUCT CONNECTED
COOLERS MUST BE ADJUSTED
Long or small air ducts have excessive air
resistance which decreases air output and
motor amperage, You may compensate for this
by adjusting the motor pulley. Use-a clamptype
ammeter to check the motor amperage
1o Check amperage at the white lead in the wiring
box,,
PITCH ADJUSTMENT
SCREW
2 If the amperage is less than the motor nameplate
amperage, loosen the pulley pitch adjustment
screw, turn the pulley _ turn clockwise, tighten
the screw and recheck the amperes Repeat as
necessary to bring the amperage to the name-
plate rating°
3. If the amperage is too high, turn the pulley coun- IMPORTANT
ter - clockwise as required. NOTE: When checking amperage with theammeter;
all louvers must be tn place in the cooler;
4 Adjust the belt tension as required (See page
13). otherwise incorrect setting of the drive
pulley will occur
STARTUP INSPECTION
Before starting the cooler, make sure al! installations
and adjustments are correct. Be sure that:
Cooler is level and duct is sealed
e Cabinet is securely fastened to the mount
o Cooler is grounded Electrical connections are
secure
o Blower wheel does not rub against housing.
o Water supply is turned on
............................... . ,,,,,_,_,,
Water line is connected securely and fittings and
crossover tube grommets do not leak
e Float is adjusted for proper water level
o Pulley alignment is OK Belt tension is OK (See
page 13)
o Pads are correctly installed (See page 13)
= Blower and both pad motors are plugged into
receptacles
o All louver clips are snapped tight
STARTUP CHECK LIST
To check out the installation follow this startup
procedure Set the control to each position and check
operation per the following chart, Be sure to open
windows or vents_,
OPERATION WITH SEARS SWITCH 32-6251
Switch
Off
Low Veftt
High Vent
Low Cool
High Cool
(Five Position)
Blower
Motor
Off
Low
High
Low
High
Pad
Motor_
Off
Off
Off
On
On
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kenmore 661.624420 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kenmore 661.624420 in the language / languages: English as an attachment in your email.

The manual is 1,49 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info