686272
12
Zoom out
Zoom in
Previous page
1/18
Next page
EN
weld joint. Filler wire is fed into the weld pool from the outside of the arc and gas shield. The
ller wire and the welding current level are decided according to the base material type and
thickness, joint form and welding position.
0.5 s
NOTE! Ensure you protect your eyes and face with suitable equipment.
NOTE! The tungsten electrode tip should be sharpened as described.
D
2xD
3.3.1 DC TIG welding
Select your required welding parameters according to the joint to be welded.
1. Connect TIG torch to the negative (–) pole of the power source, and earth cable to
positive (+) pole.
2. Select TIG welding mode by pressing the process selection button on the control panel.
3. Select a suitable welding current by adjusting the current adjustment knob.
4. Ensure your argon shielding gas supply is switched on and the ow rate is approximately
8 to 10 litres per minute.
5. Make a small test weld to check the selections made.
3.3.2 Earth return cable and clamp
If possible, always x the earth return cable and clamp directly to the work piece.
1. Clean the connection surface of earth clamp from paint, dirt and rust.
2. Connect the clamp carefully so that contact surface is as large as possible.
3. Finally check that the clamp remains fastened.
3.3.3 Tungsten inert gas welding (TIG)
Argon shielding gas is used in DC TIG welding. Your dealer will give you advice on choosing
the correct gas, supplier, and supporting equipment. Open the gas valve on the Kemppi
TTM 15V TIG torch. When the gas starts to ow, ignite the arc. The arc is activated by lightly
touching the work piece with the tungsten electrode and lifting away. A reliable technique to
practice is, lightly and briey touch the tungsten electrode to the work piece surface and then
rock backwards onto the ceramic nozzle of the TIG welding torch, so the tungsten is no longer
in contact with the work piece surface. This action makes and breaks a momentary contact of
the tungsten electrode in a controlled manner, rst making the electrical circuit and secondly
establishing the TIG welding arc the moment the tungsten leaves contact to the work piece
surface.
Minarc Evo 180
10
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kemppi Minarc Evo 180 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kemppi Minarc Evo 180 in the language / languages: English as an attachment in your email.

The manual is 1,77 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kemppi Minarc Evo 180

Kemppi Minarc Evo 180 User Manual - Dutch - 18 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info