686383
17
Zoom out
Zoom in
Previous page
1/26
Next page
EN
WiseThin, Fe group
903 1,0 Fe Ar+18%-25%CO
904 1,2 Fe Ar+18%-25%CO
913 1,0 Fe CO
²
914 1,2 Fe CO
²
WiseThin, SS group
923 1,0 SS-316 Ar+2%CO
924 1,2 SS-316 Ar+2%CO
933 1,0 SS-316 Ar+30%He+1%O
934 1,2 SS-316 Ar+30%He+1%O
Using the welding program
5. Select the welding process 1-MIG with the P9 button.
6. Press the SYNERGIC PROGRAM button to display the material group and the welding
program number. Make sure that the welding program corresponds to the ller wire and
shield gas you use.
7. Check the wire type and shield gas for the welding program in the table below.
8. Adjust the welding power with the left-hand side knob and the arc length with the right-
hand side knob.
2.2.12 SETUP features of the control panel
The machine has a number of additional features, or parameters, whose settings can be
specied with the control panel's SETUP function as follows:
1. Press and hold down the SETUP button P10 for at least 5 seconds.
2. Select the parameter to adjust using the left-hand side control knob. The parameter
name is shown in display 2.
3. Specify the parameter value with the right-hand side control knob. The selected value is
shown in the display P6. The parameter’s value is immediately stored in the memory.
4. You can exit the SETUP mode by pressing and holding down the SETUP button again for
at least 5 seconds or by briey pressing the ESC button.
All welding processes have their own SETUP parameters. For example, adjusting the post-
current for synergetic MIG welding does not aect the post-current of normal MIG welding.
The tables below show the additional features available in this welding machine and their
possible values.
Normal MIG welding parameters and their values
Name of
parameter
Name
displayed
Parameter
values
Factory setting Description
Pre Gas Time PrG 0.0 ... 9.9 s 0.0 s Pre-gas time 0 ... 9.9 s.
Post Gas Time PoG Aut, 0.1 ... 32.0 s 1,0 Post gas time,
Aut = Automatic, depending on welding
current 0.1 ... 32 s
Creep Start Level Cre 10 ... 170% 50 % Percentage of wire feed speed, 10% refers
to slow start, 170% to accelerated start
Post Current Time PoC -9 ... +9 0 Post-welding current time
15
KempArc SYN 300, 400, 500, DT 400 / © Kemppi Oy / 1117
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kemppi Kemparc SYN 500 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kemppi Kemparc SYN 500 in the language / languages: English as an attachment in your email.

The manual is 1,17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info