686414
19
Zoom out
Zoom in
Previous page
1/30
Next page
17
© Kemppi Oy / 1515
EN
Crater 4T Timer
On, OFF Factory setting is OFF ON: if 4T is selected, crater lling will last
at least time that has been adjusted by
CraterTime or as long as trigger is pressed.
OFF: if 4T is selected, crater lling will last
as long as trigger is pressed.
Creep Start
10…99 % Step: 1
OFF, CURVE (OFF=100%)
Factory setting is CURVE
CURVE means that the creep start value
comes from welding program.
StartPower
-9…+9 Factory setting is 0 Adjusts arc ignition.
ADVANCED FUNCTIONS
WisePenet
ON, OFF Penetration control selection
Penet%(123A)
-30…+30 % Factory setting: 0 % WisePenetration percent setting. Set
penetration current.
WiseFusion
ON, OFF WiseFusion selection
WiseFusion%
10…60 % or
CURVE
Factory setting is CURVE When WiseFusion is ON, it controls the
amount of short circuits in the arc. The
lower the value, the less short circuits in
the arc, and the higher the value, the more
short circuits in the arc.
MatchFunc *
Minilog, MatchCh
OFF
Default is OFF Selects the type of function for toggling
between two sets of welding parameters
during welding:
Minilog=percentage of base current
MatchCh=alternative memory channel
MinilogLevel
-99…+125 % Factory setting is 20 Sets the alternative current level to a
percentage of the base current
MatchMemChannel
0…9 Factory setting is 0 Sets the pre-dened memory channel,
where the alternative set of parameters is
stored
* MatchFunc is a function that allows you to use two pre-dened sets of welding parameters
during welding. You can toggle between these parameter sets by pressing the welding gun
trigger briey without having to stop welding.
SYSTEM CONFIG MENU
Water Cooling
ON, OFF, AUTO Factory setting is AUTO Water cooler control.
ON: Water cooler is always ON
OFF: Water cooler is always OFF
AUTO: Water cooler starts when welding
starts and turns o after a delay when
welding stops.
Cable Length
10…100 m Step: 5
Factory setting is 10m
Welding cable loop length setting for
optimising arc control.
FineCalib
0V/100A…10V/100A Step: 0.1 V
Factory setting is 1.0V/100A
Fine Tuning Calibration Point. Compensation
for varying cable resistance.
System Clock
System Clock Settings
Device List
Shows a list of connected devices.
19


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kemppi FastMig X 350MV at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kemppi FastMig X 350MV in the language / languages: English as an attachment in your email.

The manual is 1,44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info