686414

Kemppi FastMig X 350MV Manual

12
Zoom out
Zoom in
Previous page
1/30
Next page
FastMig X 350MV
10
EN
3. OPERATION CONTROL
3.1 Main switch I/O
When you turn the on/o switch into position I, the pilot warning lamp is illuminated and the
machine is ready for use. Always turn the machine on and o with the power source mains
switch. Never use the mains plugs as a switch.
3.2 Pilot lamps
The pilot lamps of the machine report its operational state:
When the green pilot lamp is on, it indicates that the machine is switched on and ready for
use.
When the orange pilot lamp is on, it indicates that the machine is overheated due to higher
than normal working loads that exceed the rated duty cycle. The cooling fan will continue to
run and cool the machine down. When the lamp is o the machine is again ready to weld.
3.3 Operation of cooling fan
FastMig X 350MV power sources incorporate two simultaneously operating fans.
• The fan is started momentarily when the main switch is turned into position I.
• The fan will start during welding as the machine reaches operational temperature, and
it will run for 1 to 10 minutes after the welding has stopped, depending on the welding
cycle completed.
3.4 Manual Metal Arc Welding
MMA electrode welding is a standard feature of FastMig X 350MV power source. To use it you
need to connect the electrode holder to the power source positive pole (+) and select the
MMA welding mode either from the power source or from the wire feeder:
• In power source control panel, select MMA/CC/CV Mode from the main menu list.
– OR –
• in wire feeder control panel, select MMA/CC/CV option with a long press of the
corresponding up-down-arrow.
NOTE! There must be an MMA memory channel dened before you can use these modes. To create
a memory channel, see the Control panel section of this manual.
3.5 Using external devices with CC and CV modes
FastMig X 350MV is a CC (constant current) and CV (constant voltage) power source. With this
function you can use it as a power source for the voltage sensing wire feeder ArcFeed and TIG
welding device MasterTig LT 250.
To use the CC/CV function you select MMA/CC/CV Mode option from the main menu of the
power source control panel.
NOTE! There must be a CC or CV memory channel dened before you can use these modes. To
create a memory channel, see the Control panel section of this manual.
… 12 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kemppi FastMig X 350MV at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kemppi FastMig X 350MV in the language / languages: English as an attachment in your email.

The manual is 1,44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info