686386
14
Zoom out
Zoom in
Previous page
1/27
Next page
26 27
B
EN With TIG and MIG processes, operate the welding gun to load the power source.
DA Med TIG og MIG processer betjenes svejsepistolen for at belaste strømkilden.
DE Bei WIG- und MIG-Prozessen betätigen Sie den Schweißbrenner, um die Stromquelle zu laden.
ES Para los procesos TIG y MIG, use la pistola de soldar para cargar la fuente de potencia.
FI Jos prosessina on TIG tai MIG, kuormita virtalähdettä käyttämällä hitsauspistoolia.
FR Avec les procédés TIG et MIG, actionner la torche pour charger le poste à souder.
IT Con i procedimenti TIG e MIG, azionare la torcia di saldatura per caricare il generatore.
NL Bij TIG- en MIG-processen moet het laspistool worden gebruikt voor het laden van de
stroombron.
NO Ved TIG- og MIG-prosesser, bruk sveisepistolen til å belaste strømkilden.
PL W przypadku procesów TIG i MIG, aby obciążyć źródło zasilania, trzeba użyć uchwytu
spawalniczego.
PT Com processos TIG e MIG, opere a pistola de soldagem para carregar a fonte de alimentação.
RU Для процессов TIG и MIG используйте сварочную горелку, чтобы приложить
нагрузку к источнику питания.
SV Starta strömkällan med svetspistolen vid TIG- och MIG-processer.
ZH 使用 TIG和MIG工艺,操作焊枪以载入电源。
EN Set the power source to the requested value and start. NOTE! Page 27.
DA Sæt strømkilden til den påkrævede værdi og start. BEMÆRK! Side 27.
DE Stellen Sie die Stromquelle auf den geforderten Wert ein und starten Sie. HINWEIS! Seite 27.
ES Coloque la fuente de potencia en el valor solicitado y comience. IMPORTANTE: Página 27.
FI Aseta virtalähde pyydettyyn arvoon ja aloita. HUOMIO! Sivu 27.
FR Mettre le poste à souder sur la valeur demandée et commencer. REMARQUE! Page 27.
IT Impostare il generatore sul valore richiesto e avviare. NOTA Pagina 27.
NL Stel de stroombron in op de gevraagde waarde en start. OPMERKING! Pagina 27.
NO Still inn strømkilden til forespurt verdi og start. OBS! Side 27.
PL Ustaw parametry źródła zasilania i włącz je. UWAGA! Strona 27.
PT Ajuste a fonte de alimentação para o valor solicitado e inicie. ATENÇÃO! Página 27.
RU Установите источник питания на требуемое значение и начните. ВНИМАНИЕ! Стр. 27.
SV Ställ in strömkällan på önskat värde och starta. OBS! Sidan 27.
ZH 将电源设置为要求值并启动。注意!第27页。
Stop validation
Start measurement
Set the
welding
unit to
<###>
TIG WELDING
Measured:
Idle U
0
50 A
100 A
200 A
300 A
500 A
Continue
Stop validation
B
10 s
!
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kemppi ArcValidator L 650 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kemppi ArcValidator L 650 in the language / languages: All languages as an attachment in your email.

The manual is 3,79 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info