686409

Kemppi A7 TIG Orbital System 300 Manual

7
Zoom out
Zoom in
Previous page
1/61
Next page
7
A7 TIG Orbital System 300© Kemppi Oy 2016 1615
OPERATING MANUAL
1.4.1 Remote control
A
E
Q
R
B
F
C
G
H
I
J
K
M
L
N
P
O
D
All the functions of A7 TIG Orbital System 300 are
accessible via one handheld device. The remote control
includes an easy-to-use graphical user interface and clear
colour display.
You can create, modify and manage welding programs.
Use adaptive auto programming for automatic calculation
of welding parameters. You can ne-adjust welding values
and electrode movements during welding. The system
automatically offers to adapt the welding program
according to changes.
1.4 Controller unit
A7 TIG Orbital System 300 power source and cooling
unit are integrated inside its controller unit. This unit also
includes a printer to print welding parameters on paper.
The parameters can be saved on a memory stick through
the USB port. Programs can be stored in internal memory
(100) and saved on a memory stick.
A. LCD: A colour display for information. The
microprocessor requires approximately 12 seconds
to properly boot when power is rst applied.
During this time, the display remains blank.
B. Cursor Up: move the cursor up the display.
C. Cursor Down: move the cursor down the display.
D. Enter: enter the item highlighted by the cursor.
E. Soft keys (4): select menu items.
These items/functions change depending on the
operation mode (e.g. setup, programming, operation).
During programmed and welding modes, the four soft
keys adjust the inner and outer dwell times. Oscillation
dwell is the time that the torch remains stationary at either
stroke end points. (“Inner” refers to the location where the
torch is closer to the weld head body, “Outer” the reverse.)
F. Home Position: To rotate the weld head until it
reaches a home position, at which point rotation
ceases.
(Home position for the 300-series head is one of 6 locations
60º apart around the guide ring.) Active only when no
arc is present, this button causes the weld head to move
forward until one of the position notches on the guide ring
is found. When using Autorewind, the weld head rotates in
reverse until it nds home location.
G. Start Weld/Start Downslope: start a weld or to
initiate downslope if a weld is in progress.
H. Emergency Stop: immediately terminate the weld
cycle and all the weld head functions.
In non-welding operation, use this button as an
“Escape” back to the Start Up screen/Main Menu.
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kemppi A7 TIG Orbital System 300 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kemppi A7 TIG Orbital System 300 in the language / languages: English as an attachment in your email.

The manual is 4,08 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info