686408

Kemppi A7 TIG Orbital System 150 Manual

42
Zoom out
Zoom in
Previous page
1/48
Next page
42
A7 TIG Orbital System 150© Kemppi Oy 2016 1615
OPERATING MANUAL
6. TROUBLESHOOTING
6.1 Operation problems
Should you experience a malfunction from your machine, please consult the trouble-
shooting sections below rst, and complete some basic checks.
If the machine malfunction cannot be corrected with these measures, contact your
Kemppi maintenance service workshop.
The problems listed and the possible causes are not denitive but serve to suggest
some standard and typical situations that may present during normal environmental use
when using the A7 TIG Orbital System 150.
Problem: Check the following:
Machine won’t work • Check that mains plug is connected correctly.
• Check that mains power distribution is switched on.
• Check the mains fuse and or circuit breaker.
• Check that power source 0/I switch is ON.
• Check that interconnection cable set and connectors
between the power source and weld head unit are
correctly fastened. See Installation section of this manual.
Dirty, poor quality weld • Check shielding gas supply.
• Check and set gas ow rate.
• Check that correct welding program is selected.
• Check correct selection on the control panel.
Variable welding
performance
• Check welding parameter settings.
6.2 Tungsten electrode rotation not concentric to tube O.D.
The tungsten electrode should maintain an equal gap ±0.1mm (±0.005") Total Indicated
Runout (T.I.R.) as it rotates around the workpiece. Variations of arc gap outside this
tolerance will cause inconsistent penetration and weld bead width.
• Collets are sized to plus .075mm (.003”) over tube diameter to allow production
tolerance on tubing.
• Deviation of more than ± .05mm (.002”0) will cause tubing to be o-centre by
more than the allowed .1mm, which will result in an inconsistent penetration and
weld bead width.
• Collets should be specied to ± .5mm when ordered.
The "wheel base" of the collets determines how squarely the weld head clamps on the two
tubes and how much "squaring" capability it has.
• If two long runs of tube are not parallel and standard collets are being used, the
weld head cannot bring the two long lengths of tube into perfect alignment.
Therefore, there will be a run-out as the tungsten electrode rotates around the
tube ends.
• Correct this by using external alignment clamp or by using extended collets.
… 42 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kemppi A7 TIG Orbital System 150 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kemppi A7 TIG Orbital System 150 in the language / languages: English as an attachment in your email.

The manual is 3,16 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info