686370
55
Zoom out
Zoom in
Previous page
1/66
Next page
55
A7 MIG Welder© Kemppi Oy 2018 1804
INTEGRATION GUIDE
6.3.8 CUST3: Customer-specific table
Interface mode = 6. Table size = 8 bytes.
Byte Bit Control (Robot -> Welder) Status (Welder -> Robot)
0 0 StartWelding CycleOn
1 GasBlow ArcOn
2 (Not in use) (Not in use)
3 WireInch Ready
4 WireRetract Error
5 (Not in use) LocalRemote
6 OnlineControl AutoManual
7 TouchSensorOn TouchSensed
1
(Not in use) (Not in use)
2
Voltage / FineTuning WeldingVoltage
3
4
WireFeedSpeed WeldingCurrent
5
6 MemoryChannel ErrorNumber
7 0 DigitalOutput1 DigitalInput1
1 DigitalOutput2 DigitalInput2
2 DigitalOutput3 DigitalInput3
3 (Not in use) DigitalInput4
4 (Not in use) DigitalInput5
5 (Not in use) DigitalInput6
6 (Not in use) (Not in use)
7 (Not in use) (Not in use)
6.3.9 CUST4: Customer-specific table
Interface mode = 7. Table size = 10 bytes.
Byte Bit Control (Robot -> Welder) Status (Welder -> Robot)
0 0 WeldingAllowed PowerSourceReady
1 ErrorReset Error
2 StartWelding ArcOn
3 SimulationMode CycleOn
4 (Not in use) MainCurrentOn
5 (Not in use) CurrentOk
6 TouchSensorOn TouchSensed
7 DigitalOutput1 (Cleaning on) DigitalInput5 (Cleaning OK)
1 0 (Not in use) MotorCurrentOk
1 (Not in use) Ready
2 (Not in use) ProgramSaved
3 (Not in use) GateDoorOpen
4 GasBlow GasFlowOK
5 AirBlow CoolingUnitOk
6 DigitalOutput3 (Spatter spray) (Not in use)
7 WireInch DigitalInput2 (Wire OK)
2 0 WireRetract WFSpeedOk
1 (Not in use) CollisionDetected
2 (Not in use) (Not in use)
3 (Not in use) (Not in use)
4 (Not in use) PanelLocked
5 (Not in use) (Not in use)
6 OnlineControl (Not in use)
7 (Not in use) (Not in use)
3 MemoryChannel WeldingMemoryChannel
4
WireFeedSpeed WeldingWireFeedSpeed
5
6
Voltage / FineTuning WeldingVoltage
7
8
(Not in use) WeldingCurrent
9
55


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kemppi A7 MIG Welder 450 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kemppi A7 MIG Welder 450 in the language / languages: English as an attachment in your email.

The manual is 5,68 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info