686368

Kemppi A7 MIG Power Source 450 Manual

59
Zoom out
Zoom in
Previous page
1/67
Next page
59
A7 MIG Welder© Kemppi Oy 2018 1824
OPERATING MANUAL
5.2.3 Wire feeder errors
Code Description Severity Measures
42 WIRE FEED MOTOR HIGH CURRENT
The wire feed motor current is close to the current limit when the motor is running.
The wire feeder rolls are too tight, the wire spool brake is too tight, or the wire liner is
dirty.
Warning Check and replace the consumables in the wire feed unit and the torch.
43 WIRE FEED MOTOR OVERCURRENT
Current limit is exceeded while the wire feed motor is running, and the motor is
stopped. The wire feeder rolls are too tight, the wire spool is too tight, or the wire is
stuck.
Error Check and replace the consumables in the wire feeder unit and the torch.
44 NO WIRE FEED SPEED SIGNAL
Wire feed motor tachometer signal missing. The tachometer is damaged or the
wiring is broken.
Critical error Contact the maintenance service.
50 LICENSE ERROR
An attempt was made to use an optional accessory, welding program, or a specic
setting for welding that has not been activated using a license code.
Error Acquire a license for the optional function you want from the device provider.
51 THE REAR FEED WHEELS ARE LOOSE
The rear feed rolls are loose. The wire feed speed is slowed down or varies.
Warning Tighten the rear feed rolls.
52 THE FRONT FEED WHEELS ARE LOOSE
The front feed rolls are loose. The wire feed speed is slowed down or varies.
Warning Tighten the front feed rolls.
53 COLLISION DETECTED
The collision sensor has been activated. The welding torch mounted on the arm of a
welding robot has collided with the welding piece or another obstacle.
Error Reverse the robot arm until the torch no longer touches the obstacle. Check
the torch in case of damages.
5.2.4 Welding curve errors
Code Description Severity Measures
81 CURVE FILE NOT FOUND
Internal program error. The selected synergic welding curve was not found in the
memory. The system memory card is detached or defective.
Error Switch o and restart the power source. Contact the maintenance service if
the error is not resolved.
… 59 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kemppi A7 MIG Power Source 450 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kemppi A7 MIG Power Source 450 in the language / languages: English as an attachment in your email.

The manual is 3,76 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info