686368

Kemppi A7 MIG Power Source 450 Manual

39
Zoom out
Zoom in
Previous page
1/67
Next page
39
A7 MIG Welder© Kemppi Oy 2018 1824
OPERATING MANUAL
4.4.2 Turning user identification system on
The user identication system can be turned on from
either the web user interface or the setup panel.
Setup panel
Turning the user identication system on requires ad-
ministrator privileges in the setup panel. Go to the Main
menu > User settings and select a user with administrator
privileges. Provide a valid PIN code to log in. In the User
settings menu look for the User mode parameter and se-
lect the desired value (ON). Press the Save button to save
the settings.
Web user interface
In the web user interface the user identication system
can be turned on without user login. Note that you still
need to have a valid administrator PIN code available.
The system requires user login immediately after the user
identication system has been turned on and the user
identication system cannot be turned o without admin-
istrator privileges.
Go to the Settings > Users page and switch the User iden-
tication parameter on. A pop-up dialog with Save and
Reset changes buttons will appear at the bottom. Press
the Save button in the dialog to save the settings. The user
interface will go to a login page automatically. Select an
appropriate username and provide a PIN code to log in.
4.4.3 Creating new users
Creating a new user requires administrator privileges.
Welders and supervisors cannot create users. There are up
to ten user accounts available in the system. If all ten user
accounts are in use, a new user cannot be created.
Setup panel
Go to the Main menu > User settings and provide your PIN
code to access the User settings menu. Go to the User acti-
vation and select a user number from the USER1 - USER10
until the text (Disabled) appears under the username. This
means that the particular user account is not in use. Click
the Select button and switch the user to Enabled. Press
the Set button. The new user is now created with welder
privileges. In order to change the user privileges, see Sub-
section 4.4.5 "Changing user role".
You cannot congure usernames in the setup panel. In
that case users are displayed by their system name (USER1,
USER2...). Use the web user interface to congure the
usernames.
TThe default PIN code for the new user account is 0000. To
change the PIN code, the newly created user needs to be
logged in. See Subsection 4.4.7 "Changing pin code" for
more information.
Web user interface
Go to the Settings > Users page. In the web user interface
the user identication system must be turned on to ac-
cess user settings. Available unused user accounts are
displayed in gray font. Click the text Click to create a new
user on the account you want to create and type a name
for the user. The user interface will make other options au-
tomatically available and a pop-up dialog with Save and
Reset changes buttons appear at the bottom. Select the
role for the user by clicking the Welder, Supervisor or Ad-
ministrator buttons. Click the Save button to save the set-
tings. The new user has been created with the default PIN
code 0000. To change the PIN code, the newly created user
needs to be logged in. See the Subsection 4.4.7 "Changing
PIN code" for more information.
The Settings > Users selection in the side menu is not
visible to welders and supervisors. If you cannot see the
selection, you do not have the privileges to change user
settings. Log out and log in using another account with
administrator privileges.
… 39 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kemppi A7 MIG Power Source 450 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kemppi A7 MIG Power Source 450 in the language / languages: English as an attachment in your email.

The manual is 3,76 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info